Advice needed: It's time for a new DAC


Hello People of Audiogon!

I received some help a little while back when I was considering upgrading my speakers so I am looking to the community again for guidance and opinions.  It is time to upgrade my DAC.  

 

My current system is Sasha DAW's driven by a Luxman L-509X.

 

The three DAC's on my short list are:

 

MSB Discrete
Berkeley Alpha V3
Chord DAVE

 

One thing to note is that I am in Canada so many brands are difficult if not impossible to audition.  

My priority is "musicality" or "soul".  What's this?  Well to me, it means feeling.  The Luxman and Sasha's well convey musical emotion and that is important to me.  I don't know how to describe it better beyond that.  They have flow (perhaps PRAT, to use another vague term).  Sounds have meat to them and texture.  The music feels real.  

 

The second priority is three dimensionality.  

 

The third is resolution.

 

My one caveat is no tube DAC's.  Tubes, for me, just don't work well based on my listening style and habits.  I love tubes, I've owned tubes and tubes are wonderful, but as things are now, I just don't want them in a DAC.  Perhaps they will find their way into my system in a pre-amp in the future.

 

I listen primarily to Tidal but MQA is not a priority for me.  I would switch to Qobuz but they were not available in Canada until recently and all my play lists in Roon are with Tidal tracks so I suspect a switch will be a real headache, but I digress. My point is MQA isn't really important and DSD isn't necessary either.  

 

Of the above DAC's, if you have heard them, what are your thoughts/opinion?  

 

Thank you in advance,

-Paul

 

 

bigfatpaulie

I have a chord DAVE and it will be for sale next week. Great DAC and I still absolutely love it. M-scaler too.

But I decided to try a Lampzator GG3 and it is spectacular. Tremendous soundstage, realism, and sharp-tight-defined from top to bottom.

Big fan of the DHT and I think SE is the way to go (vs balanced). I also ordered with Volume Control and basicly use it as a preamp. really increased "slam" or "punch" and I think that is the DHT acting as a preamp.

Jerry

op y ou are not providing enough information

 

what are you using currently using?

how wil you feed the dac?

we would recomend the Aqua hifi forula it is very musical yret has great resolution plays all high res files.

it is also completely upgradable so if aqua impoves the dac you can grow with the dac

 

the berkley wouldnt be on my list as you need an additional interface box for usb and most high res sfiles play over usb

the chord dave is very good but it is a touch lean

Daveand troy

audio intelect NJ

aqua and chord dealers

Berkeley Alpha.

 

I love my Audio Research Reference CD9SE. I had a Berkeley Alpha Reference 3 in my system for a couple weeks. I found the ARC a tad more musical… my preference, but the Berkeley was ever so much more detailed with nearly all the musicality. It is an outstanding DAC.

 

Beautiful speakers you have. Have you tried a thick carpet in front of your speakers and you might try making a heavy absorption panel to put in front of the fireplace when listening.

Hi @audiotroy 

 

Thank you for your reply.  To answer your questions:

what are you using currently using?
An RME-ADI2fs

how wil you feed the dac?
A Lumin U1

 

How does this information help you answer my initial question?

 

I use AES/EBU right now and I would likely keep it the same, hence why the Berkley made the list.  For context, I have, in the past owned an MSB Analog, a Berkley Alpha V1 and a Chord DAVE.  I owned each, however, when I was in a condo and I was exclusively using headphones.  Now, I exclusively use speakers. 

Hello @ghdprentice !

 

Thank you so much.  I really appreciate your comment as you've owned the Berkeley.  The CD9SE...  WOW!  I really adore AR stuff.  The some of best amps I've heard (save the Boulder 2160) have been AR.  

 

Thank you for your kind words.  My wife doesn't like carpet, however, when I have a serious listening session, I do put down two thick blankets on the floor.  It's an interesting idea you had about putting absorption in front of the fireplace. I have a bit of a fuzzy center image because of it and I never considered movable panels.

 

I have 4 5" thick Vicoustic panels on the walls behind the DAW's.  They make a minor difference as-is, but I wonder if they were on a discrete stand with casters that I rolled out (like the blankets on the floor) if that would help...  Very astute observation and thank you for the advice.

 

@bigfatpaulie When I want to evaluate DACs I use my headphones (RAAL SR1a or CA-1a) to really hear my gear. When you had your phones which DAC did you like the best? The DAC I own now is what sounded the best on my phones.

Tidal vs Qubuz. I have both and I do not even think about it. Just enjoy the music with which ever has the tune I want.

I grew up in Toronto and there were a lot of good shops then. I still see some of the same stores around and some new ones with even higher priced gear. 

BTW - how long is your speaker cables?

 

 

@bigfatpaulie In all honesty, the T+A DAC 200 should be in that list above considering all of the priorities you list (soul, holography, and resolution). I've said it before but I still think the DAC 200 is the best I've heard under $15K. In full transparency I am a T+A dealer, but I've had more than one customer switch from the DAVE to the DAC 200 because of its improved sound staging ability and soulfulness.

I’m really liking the Cen.Grand Deluxe DSD DAC, but hell... I LOVE my Tambaqui. I’d recommend the MMT, but the Cen D³ is excellent, and my biggest praises for it are in comparison with yet another DAC, two Intergarated amplifiers and a power amplifier

Of the three DAC’s you listed I would pick the Berkely V3, since I’ve heard less criticisms about it, but truthfully have heard less overall about it compared to the others.

My Cen D³ bests my T+A DAC200 in sound stage size, depth, and especially transient decay. I swear you can "hear" the air in the room whilst the artist was recording in between notes and at moments of silence. Just a very cool sound, almost to the effect that my Luxman M10x brought to my system when first listening (prior to the Cen D³). Secondly the Cen D³ made the sound presentation for my Technics SU-R1000 almost indistinguishable from my Riviera labs Levante. So the Cen D³ brings a "tube like" sound to a Class AB digital integrated amp that neared the liquidity in sound of an amazing hybrid amp. I was so impressed at how much character the SU-R1000 took on with the Cen D³ (good character at that).

Ultimately my MMT is my favorite, but the Cen D³ with the Levante just makes what I love about both pieces of gear stand out even more, not too mention the Cen D³’s volume control is better then the somewhat finicky Levante and allows me to run the JL subs via RCA out.

All and all I highly recommend the Cen D³.

My only digs are that the company’s reputation is unproven along with product service/support. I’ve ran into customs tearing apart my unit packaging and just throwing everything back into the box. I had a coaxial input issue with this unit and am otherwise am awaiting a second replacement unit. But still would recommend it. I’ve been swapping all my gear in and out with it and it sounds great with pretty much everything I own at all price points.

 

@blisshifi I could 100% see how a DAVE owner would love the DAC200, but I’m going to be listing mine now having the Cen D³. The T+A build quality and feature set is just incredible and in my heart of hearts wanted to keep the T+A because I really like how much time, attention and quality craftsmanship went into it, but I feel it’s DSD DAC far outshine it’s Burr Brown DAC chip, which kinda let me down.

It’s resolution and vocal forward presentation would again attract DAVE fans.

@bigfatpaulie that fuzzy center image is most likely due to first reflection points not being treated. The fireplace has some say in it but it’s negligible. The direction of the sound your Sashas put out is forward with tweeter and midrange dispersion to the sides at a slight angle. I don’t have a fireplace but had exactly the same issue. Cured by treating the first reflection points and installing bass traps to tighten up and refocus the lower registers. Snapped together nicely. 
May be talk your wife into hanging heavy curtains over that window by the right speaker. Mean time, toeing the speakers in to fire directly at your listening position should help with imaging as well.

As to the DACs, you have a nice list. If you use Tidal and don’t need DSD, go with the Berkeley Alpha 3 ( has MQA processing capabilities). However, keep in mind that it has no USB input and you will be using AES with it most likely, which means the clock in your streamer is what you’re going to be relying on. Not sure how good that section of the Lumin is. 
With the DAVE you can use USB (will most likely sound significantly better using that interface with your streamer) but you don’t get MQA. Chord tone is superb though. 
With MSB, you get awesome USB implementation, MQA and DSD capabilities. 
So if I were you, my choice would be the MSB Discrete. 
Just thinking out loud….

@bigfatpaulie 

@audphile1 makes a bunch of great points. I left out the Cen D³ doesn't have I²S in if that's something that you wanted, and converts all incoming signals to DSD up to 1024 (no MQA).

There might be an upgrade in the future and has a open module slot.

Some good DACs recommended here,don’t exclude the Weiss 501, amazing DAC. See the Steve Hoff review on You tube.

Save yourself some $$  the Excellent T+A 200 dac can compete with Anydac up to $15k and compared to the chord Dave much more musical and at $7200 

before discounts and HQ player built in a true Audiophile bargain 

check out all the Great reviews and get a demo unit to try out .

that ones next on my list.

OP I have a bit of a fuzzy center image

In my experience, unless you find the natural sound system like the right speaker in the below video, the fuzzy/empty center image is impossible to avoid. All audio systems sound unnatural and fuzzy/empty center image like the left speaker in below video. Alex/WTA

A sample of the natural sound system.

Original music

Samples of unnatural sounds.

Hi everyone!!  Thank you for all the input.  I'll do my best to answer everyone, but if I miss someone  I'm sorry.  

 

@yyzsantabarbara Of the DAC's I used to own, my favorite was probably DAVE, however, I was using it with a DNA Stellaris amp, fancy glass, and modded HD800's.  It was a very different system than my speakers and synergy is important.  I also had different goals than I do now.  My speaker cables are way too long.  They are also basic and will be replaced down the line.  The amp is in the basement, however, I am going to move it so it is basically just below the ceiling so the cables, in the end, will likely be 4 feet or so.
 

@blisshifi I originally had the DAC200 on my list because of the all the hype.  I also took it off because of all the hype.  Guys like Huff, it seems everything new is "the best" so I just ignore him and people like him.  I'be been around long enough to know that there is no such thing as a "giant killer" or a $15k item for $7k.  Too much hype for me, I guess...

 

@ja_kub_sz I've never heard of the Cen.Grand.  Thank you.  I have heard the Mola Mola and I guess I am alone in my feelings about it.  I don't care for it at all - I find it thin and lifeless sounding.  I also found it had a lot of digital grain.  For reference, I feel the same about the PS Audio DSD.  They aren't for me personally.

 

Thank you @audphile1 .  The speakers are toed in.  It could likely be solved by more room treatment (eg curtains) but things like that just aren't an option.  I have to work with what I have.

 

@vicdior Thank you for the Weiss suggestion.  It's another one of those hyped up Huff DAC's...  First the DAC200 was better than anything for twice the price, then the 204 was better than the DAC200 at half that price...  It just doesn't add up as then a 204 is better than any $15k DAC.  It's all too cloudy for me.



 

@bigfatpaulie GIK sells stands for the panels. Mount a thick GIK 244 panels on these stands for each first reflection point. Store these two panels in the garage or something like that, and break em out for your critical listening sessions. Then stow them away. You can even do the third panel in front of fireplace. May be that’s an option.

 

The DAC204 and DAC205 are relatively affordable options to Weiss Engineering’s higher-grade units such as the DAC501 and the HELIOS. They do not have the onboard digital processing capabilities of those units, nor do they include headphone outputs or remote controls.Also,it all depends on what gear and cables, speakers you use to get that synergy system that sounds pleasant to your ears.There are also plenty of other reviews you can search on the web but better still ,if you can go listen at a dealer.Good luck with your choice.

@bigfatpaulie I am using a Schitt Yggi+ LIM DAC that I like a lot. I have a Benchmark DAC3B in my Livingroom system, The plan is to get a PlayBack Designs Dream DAC to supplement the DAC3B. You may want to read up a bit on the PBD. I wanted a DAC that was FPGA based and the PBD designer made the first FPGA based DAC. In fact, he mentored Ted Smith at PS Audio. Nagra DACs are also using his lower end tech.

I already have a lower end PDB streamer, and it is comparable to the Lumin X1 (using fibre) and the Sonore OpticalRendu (fibre again). At the moment I am only using SPDIF on the PBD streamer and it can still compete with the other 2. It has fibre but I need get a PBD DAC to use that feature. I figure if he can make a streamer this good his DACs should be spectacular.

The other FPGA DAC I was considering was a Rockna. I did not consider the DAVE or the PS Audio.

The following thread could be helpful for your DAC ideas:

Audiogon Discussion Forum

If you mostly stream with ROON, JRiver, or a computer you may want to talk with a fellow Canadian Mitch Barnett. The dude is a genius at what he does and is a relatively cheap alternative to resolve speaker placement. The adjustment in the digital signal is done BEFORE the DAC. All work is done remotely.

He is now also making a name for himself in the headphone space. I used his tech when my room was not acoustically nice as it is now. I no longer use his solution (with ROON) but it is genius level stuff and my safety net for speaker room interactions. In my opinion, the most important aspect of good sound.

Digital Room Calibration Services, Convolvers, Headphone Filtersets (accuratesound.ca)

Monoblock amps will solve you speaker cable issue. I use Benchmark XLR for my lengths over 15 feet. Those cables are cheap and do the job well.

Check out the current review of HEM Ferrum Audio Products

EISA HiFi chapter members gave WANDLA the recognition by awarding it Best DAC of the Year, we just were beyond ourselves. The Converter proved to be The Best Converter. Our EISA winning streak began two years ago, back in 2021, with the success of our Ferrum HYPSOS hybrid power system

Both pieces $3995

Search Wandla reviews

When I was looking to get an integrated amp, I demoed the Luxman 509x and it was rather good. Then I made the mistake of listening to the Luxman c900u + m900u with the Luxman DAC in the then top end Luxman SACD player. The separates are significantly better than the 509x, mainly because of the stronger power supply. I mention this because I see the m900u on the used market at lower and lower prices. The m900u can also be run in mono.

The Luxman DAC is what a lot of people consider musical. Not my taste since I like a bit less warmth but that was a great system.

I think I just motivated myself to call Mitch to see if he can improve on my Livingroom system. It is a Yamaha NS500 speaker + CODA #16 amp. The speakers are a bit too close to the front wall. The sound is great but maybe it could be better. My ceiling is over 20 feet so maybe that is why the sound is good.

@ja_kub_sz ,

Before you sell your T+A, make sure that you have have enough hours on the PCM side of the DAC. There are a couple of posters on the HeadFi forum who recently found out that the PCM section took about 200+ hours to come on it's own. In fact these guys liked the PCM presentation as much or slightly better than the DSD presentation. But this is a headphone forum and they do not have as much experience with loudspeakers.

Good luck!

@milpai good to know... I feel like I've put at least that into it, but yeah I'll do some more listening.

DAC's have a huge impact on ultimate performance.  Synergy is also a real thing in my experience. Some DAC's I liked with one combination of gear, but not with another. Try to demo as much/many as you can if possible (not always easy).  Old timers, like me, all have our favorites. My faves Ayre and Bricasti.

@bigfatpaulie , I own the Tambaqui and for a while I didn’t quite know how I felt about it. But I was putting it in standby all the time, which was my mistake. I realized that to sound its best, it takes quite a few hours - maybe 10 or more.

Not sure if this applies to you but I also found it to be lifeless and with a bit of glare until I realized I should just leave it on. I thought it didn’t quite have enough impact and as such wasn’t engaging. Now that I leave it on, I think it is fantastic - high resolution and dynamic but with a hair of lushness to it that to my ear at least makes it musical.

I own a TotalDac D1 and a Baetis Revolution streamer streaming Tidal. I think in your price range yiu should 

Take a look at TotalDac

 

Post removed 

I highly recommend the PS AUDIO Directstream DAC MkII. You can hear Beautiful music through it.. Enough said...

@bigfatpaulie, the Meitner MA3 hits your first two requirements, especially the first one, plus it's made in Canada!    I personally found its resolution very good but not great, compared to a few other DACs I've also owned.   I've owned the Berkeley Alpha V2, a Bricasti, and currently own a Weiss that I think is a bit more resolving than the MA3.   The MA3 though definitely has that "Sounds have meat to them and texture.  The music feels real." quality,  as I replaced a very fine MojoAudio R2R NOS DAC with it and felt like it was a big upgrade.

Hello @bigfatpaulie,  lots of good advice here!  @ghdprentice is always spot on.

I have had a friend's Dave in for direct comparison to my MM Tambaqui.  He sold the Dave and got a Tambaqui if that tells our story.  It sounds great buy it self with internal streamer or bridge, but excels when combined with the Grimm MU1 in my case, or another great streamer (Aurender N20 or better).  Many great reviews call the Grimm / Tambaqui a match made in heaven (Netherlands).  I have one stand alone Tambaqui, and another in the MM Makua Preamp; both are excellent.

 

Hi Everyone!

I thought I would pop in and post an update on my DAC journey.  First of all, I really appreicate all the help, advice and guidance post here and that I received though PM's.  Thank you all.

 

I ended up audtioning a few DAC's.  To name a few (and this not an exhaustive list):

 

Chord DAVE

Berkely Alpha V3

MSB Premier

Bricast M1

DCS Bartok APEX

Linn Kilmax

AudioNote (ANK) Level 5

PS Audio DSD

T+A DAC200

Weiss DAC501

 

I had the majotiy of these at home, in my system for at least a few days.  

 

Long story short the DAC that won my money is the Playback Designs MPD-8.  Frankly, compaired to the rest, it wasn't even close in most cases.  My second favorite was the MSB (for quite a bit more money).  I know it will sound trite but the Playback is the most musical sounding DAC I've ever expericened.  It's smooth without being dull.  It's detailed without being clinical.  It's dymanic without being grating.  To me, it's the full-meal deal.

 

Best,

-Paul

Oh, I should also mention I upgraded my L509x to a Luxman M-10x wink

 

I've had a busy few months!

@bigfatpaulie very nice of you to pop back in and share your progress. 
That Playback Designs DAC is really nice. Enjoy!!!

I recommend a serious listen to a Meitner MA3.

A Canadian product that to my ears sounds great.

Hi @rja .  I actually did audition the MA3 at a dealer and based on that I wasn't motivated to do an in-home demo. 

@bigfatpaulie

Beautiful DAC, congrats! Wow, you really put in your homework. 

I am sure many and I would love for you to share some listening notes for each of those DAC’s if you can muster up some audiophile adjectives. wink

And if you find a moment take some pictures and list your system in virtual systems, I would like to see the rest of your kit.

Sure @mclinnguy .  I took  A LOT of notes when I auditioned but here's a very brief summery.  

 

Please keep in mind, if anyone loves one of the DAC's below, that's cool.  Below are MY OPINIONS.  Not fact.  We are all different and have different preferences.  If you think DAC XYZ is the "best" then good for you, enjoy it!  Don't like some jerks opinion (ie me) on the internet take anything away from that. We can all like different things, and that's just fine.  You will never hear my system nor me yours, so it doesn't matter so long as you love yours!

 

Also keep in mind, I am mostly speaking about the negatives.  The reason for that is that for the most part, all these DACs did most thing well.  Assume if I didn't mention an aspect of the sound for that DAC, it means it probably did at least a passable job of that aspect. 

 

Chord DAVE
I owned a DAVE years ago. According to the distributor, I had the first one in Canada, so I know this DAC pretty well. It was the last "good DAC" I owned back when I was a headphone guy, so I thought it was well worth a home audition. Immediately, I really liked it, and the M-Scaler improves everything by a noticeable amount. Honestly, it was the first DAC I brought home, and I was pretty sure I would end up with it in this case too.

 

Berkeley Alpha V3
I also used to own a V1 of this DAC, and I have very fond memories of it. Listening to it now, it's a very detailed DAC, but it lacks separation, which is odd. The presentation, as a result, feels very "out of sorts," and it has a good amount of digital glare: that is to say, it sounds distinctly digital. It isn't smooth or organic at all. If you wanted something for studio work, this would be a good choice.

 

MSB Premier
This is an interesting one. I actually preferred it to DAVE+M due to it presenting a more cohesive presentation. What I mean is that the DAVE+M and the MSB presented a lot of detail, but the DAVE+M images were smaller in space than the MSB. The MSB felt more like a performance in front of you. For example, a guitar is life-sized with the MSB, whereas with DAVE+M it is 50% smaller. This gives the DAVE+M better separation, but it loses in naturalness.  This became my new 'to beat' DAC.

 

Bricasti M1
I LOVED this DAC... but only for a weekend. It's SUPER dynamic and punchy. It's the AC/DC of DACs: I don't care how much anyone loves AC/DC, sometimes you need a break from them. It's the DAC you buy if you want to wow your friends. It's lively and energetic but does have that same digital glare that the Berkeley had, but with more PRAT (dynamics and bass kick). For things like classical or jazz, it is fatiguing.

 

DCS Bartok APEX
Well, it's very detailed. And it's wonderfully made and looks great. Other than that, it didn't do anything for me. Years ago, I had a DCS Debussy that, to this day, is the WORST DAC I've heard. Seriously, the headphone jack on your phone is better than a Debussy. The Bartok is much better, but it's thin and mechanical sounding. I think this is the DAC to use at a Hi-Fi show (like the M1) because it will wow with its details. It's also a good DAC if you want bragging rights but don't really listen to much music.  I'll let you guys know when DCS sues me for saying this.

 

Linn Klimax DSM
The Klimax... They misspelled Climax and missed the mark in my eyes. I think it's a high-margin product because the dealer practically made me take it home for a demo. It's thin and digital-sounding, similar to the DCS, but with a more compact soundstage, which in this case, helped.  It's a GEOGIOUS looking unit and it's that's a priorty, it's had to beat.  Please keep in mind that I am being harsh on this unit (it's better than I am making it sound) but not at anywhere near the MSRP.  If you can get one at 70% off, it's a good choice.

 

AudioNote (ANK) Level 5
What can I say about this one... I built one years ago for a friend, and this one was loaned to me by a friend. It's like a slightly worse Premier (for less money, but adding tubes) in that it had a really wonderful presentation size but did a better job at layering. Where it lacked was detail retrieval, if that really matters to you. For the money, and if you are willing to build one and are okay with tubes, it's a lovely, musical DAC.

 

PS Audio DSD
I don't like this DAC. To me, it's sandy sounding. It is the least smooth of all the DACs, and the sound has a literal grainy quality. It is also one of only 2 DAC (the other being the ANK) that had an audible noise floor.  Hard pass.

 

T+A DAC200
Okay, I will put on my flame suit now. This DAC is good, but it isn't a "giant killer." Now, in all fairness, I used it like a normal person (Lumin as a streamer), and I didn't use a custom-built PC with HQPlayer, etc. But adding the PC and HQPlayer (not to mention the hassle) bumps the price of this DAC well past $7k, and I would get a used DAVE every day of the week over this for about the same money.

 

Weiss DAC501
The midrange on this DAC is really special—some of the best and probably only really bested by the ANK of the above DACs. The bottom end doesn't have the control or kick of the M1, and it doesn't have the resolution of the DAC200. It's the opposite of the M1 in that if you NEVER listen to AC/DC and only listen to jazz, this might be a really good choice.

 

Meitner M3 (because it was brought up)
I didn't take this one home unlike the others, so take this (actually everything I say) with a BIG grain of salt. I heard it at the dealer, and it's a very warm DAC. It's perfect if you want lovely-sounding background music. There is nothing offensive about the sound of the DAC, but as a result, it's flat and dry sounding. Totally unengaging and dull, lacking the resolution of the better DACs on this list.  Made in Canada or not, it wasn't for me.

 

Playback Designs MPD-8
I discovered this by chance. I was at a dealer looking at the Berkeley, and they had an MPD-8. When I saw the oddly shaped gray box, I thought it was an old, goofy-looking CD player they got in on trade or something. One of those pieces where the guy says something like, "Yeah, it's from 1992, but it has the special Sony laser that they only made on Wednesdays for 2 months that's the best ever built" or whatever. I passed when he first offered to audition it because I didn't want a CD player. He suggested I just give it a quick try anyway, as it was already hooked up. Immediately I was surprised—it was detailed with life-sized images. It has the depth of a good tube system and absolutely no digital grain. It offered all the dynamics and punch I could ever want with zero fatigue. This DAC was a total surprise and came out of nowhere for me. It sounds like hyperbole, but take the best elements of all the above DACs and combine them into one, and you have the MPD-8. To me, this was the choice, and the second best (MSB Premier) was lacking across the board (aside from looks) for substantially more money.

@bigfatpaulie

Please keep in mind, if anyone loves one of the DAC’s below, that’s cool. Below are MY OPINIONS. Not fact. We are all different and have different preferences. If you think DAC XYZ is the "best" then good for you, enjoy it!

And I do own one of these DAC’s, but knowing that I still would expect nothing less than someone telling their truth on what they hear. Hey I, and everyone else who owns one of these DAC’s, knows what it sounds like, and what someone else says has no impact on my impressions of it, and it shouldn’t with them also.

Additionally you, with your ears, given a different room, different speakers, different other components, different digital connections/cabling, (perhaps the least preferable one recommended by the manufacturer) would have probably had a completely different outcome.

Thanks! I (and I’m sure others) appreciate it! Sharing listening impressions is what this forum is all about. yes

@audphile1 

 

It is the current MK2.  It was loaned to me by a dealer (In Canada there are PS Audio dealers).

@bigfatpaulie 

 

Thanks. I have heard several of the DACs you talked about, I have to agree with your assessments. 

@bigfatpaulie quick question on a bricasti…did you experiment with different filters and clock settings? Having it on Linear 0 filter setting may create the impression of what you described. When I had the M3 I used it on Minimum 0, ClockWide. Very natural sound. 
 

Also, I was hoping PS Audio would address the items you mentioned with the MkII release…I was pretty sure you were talking about MkI the way you described it. Too bad…

Also, I was hoping PS Audio would address the items you mentioned with the MkII release…I was pretty sure you were talking about MkI the way you described it. Too bad…

Well, take the comments with a grain of salt: the PS Audio mkII retails for $8000

OP’s top two choices here retail for $28,000 ~ $30,000, so once again typically one gets what one pays for, within the context of the law of diminishing returns. 

Clarification question though @bigfatpaulie since you mentioned a "CD Player" appearance, is that not the MPS-8 you have?

(did you all catch that? "grain" of salt? ha ha)

 

@audphile1 So full disclosure, I used to own the M1 about 8-9 years ago when I was a headphone user.  I really loved the DAC at the, especially with the HD600's connected directly to the balanced out's.  Because of my fond memory of it, I wanted to audition it again. With this time, I did play with all the filters but the one I settled on was minimum 4.  With that said, I did find the filters offered a generally subtle difference, personally, and the M1 sounds like the M1 regardless of filter setting. 

 

@mclinnguy Yes, I did end up with a more expensive DAC but the PS Audio was also not the cheapest on my list.  Both the ANK and the T+A DAC200 were less money.  The reason I auditioned the PSA was that the dealer that sold me my speakers offered it to as they felt it offers excellent value and was well worth a listen.

 

And you are correct, I noted the error about the PB names after I posted but I couldn't edit my post.  The PBD unit I first saw/demo'd was the MPS-8 (DAC/Player/Streamer in 1 box) as they did not have a MPD-8 on hand.  I did my auditioning using the MPS-8.  The unit I bought is the MPD-8 (DAC only) as I did not want the CD player or streaming functionality.  According to Andreas Koch, who was very kind in answering all my questions, was very clear that as a DAC only the MPD-8 is the better choice, though the units are very close sounding.  Having heard both, I would agree.

@bigfatpaulie thanks!
I agree the filter is not going to have as much impact on sound as changing a component or incorporating room treatments. And man with the Wilsons they’ll seek you out and kick your butt with good or bad whatever they are fed. So I get how you arrived at the results you’ve shared. thanks again this a timely thread as I’m on a market for a new DAC. 

That's cool @audphile1 !!  Though, I don't envy the search that lies ahead of you!  I took me MONTHS to settle on one.  Hopfully you find yours faster than I did mine.

If you don't mind me asking (and I am just being nosy here) what do you have currently and what's on your short list?

Good luck with your hunt!