Brand New Vinyl Static and Pops


Nothing major, but annoying.

Could it be because I was spinning old dirty vinyl which made the platter dirty/dusty?

I'm about to buy the humminguru. Does anything go well with it?

 

128x128jjbeason14

I bought MOFI Micheal Jackson Thriller, brand new sealed and when I spin for the first time, Billy Jean and another track skipped many times. When I spin the 2nd time, it skipped lesser, lesser on the 3rd and it spin without skipping when I spin for the 4th times,
New n expensive vinyl can be dirty too, our needle will pick up those dirt and we need to clean the needle.
Some new vinyl give humming sound....This is the world of Vinyl.
Its best to clean every vinyl that come by either with the expensive Ultrasonic cleaner like Degritter/ KLAudio etc or some manual effective cleaning system. I use the cheap "ManualSonic" with  Audio Technica record cleaning kit. Not bad.  
It sound great still.

I agree with a couple of the other comments - clean ALL records in a US cleaner before playing - even new ones - you have no idea what gunk is on there from the pressing process. I am still amazed at the junk on the bottom of my US cleaner after cleaning a bunch of new records, and even records that have already gone through the US cleaner. More stuff comes off. I also clean the stylus before and after each play with an Onzow Zerodust. I may purchase a Furutech device per another comment. My two cents..... thx

You wanted 2 cents? Here is mine. I ultrasonic clean new (manufacturing particles ARE in the grooves. I can hear the difference) and used. If you don’t have an ultrasonic then devise some kind of system of cleaning that leaves a minimum of residue so you can hear what’s in the grooves accurately. Finally, and I know some members will freak, but I clean my stylus after each side of play by lightly dragging a thin strip of magic eraser across it. That dislodges accumulated gunk. I then lightly wipe it with the Onzow zero dust stylus cleaner. I know it sounds like a lot. Some here will dismiss both. I wouldn’t do it if you have shakey hands or god forbid, been drinking or other mischievous behavior. Everybody on here has an opinion. Use your own judgement. This is what I have found consistently works for ME. But I have approximately 900 LPs that I play regularly. I rarely hear clicks and pops using a Microreach stylus on my cartridge. The few LPs that skip were bought used and had legit flaws. Take  care of your LPs and stylus and they will take care of you. 

New vinyl is a crapshoot. That makes me buy CDs but mainly stream on Qobuz. Only bought two vinyl this year. By now I would have bought at least 20 in previous years. Nothing like moving on up with the times.

I often find new records that are dirty right out the jacket especially if they have paper sleeves. Always clean a new record as most have a film on them that cleaning will remove. Never blow the visible debris off your record with air from your mouth as this will leave minute particles of moisture that will harden and cause problems. And do not forget to keep your turntable platter or mat clean so that dust or debris is not transferred to your records especially if you use a record clamp.

@lewm I noted lots of modern pressings aren't that quiet and sometimes reveal surface noise and even deep warps.

 

I wouldn't argue that from a perfectionist point of view it is not a good idea to clean "new" LPs, but I do play new LPs right out of the jacket without cleaning them, very often, and I cannot recall a problem due to dirt (ticks and pops).  Sure, some are warped and some are off center and some are both warped and off center, but not dirty enough to cause mistracking or ticks/pops.  Just my personal experience.

I wish I were a magical King Midas with the ability to summon every musician I have a hankering to hear to my listening room. The closest I seem to be able to get to this, though, is my stereo. I guess it'll just have to do.

Small Micron Dimension Particles are easily responsible for creating the interferences referred to.

All Ambient Air in a Industrial Environment will have many types of Particulate of this dimension suspended in the air and able to contaminate a surface and embed in the LP Groove.

An area that has a heavy burden of Traffic or a Local Railway, where there is Production Facilities will also have to contend with excesses of Metal Particulate suspended in the Air.      

Release Agents used on the LP during production are also most likely to have a Small Micron Dimension Particle suspended in the solution, this could also be a Metal Particle in a excessive quantity, depending on the siting of the production facility used.

LP's are 'not' made in a Laboratory Environment where Filtering of Contaminants is a vital control measure. 

The location of a Production Facility and the Quality Control measures followed during the production are most likely a cause of various levels on contaminant collecting prior to packaging and sealing.   

jj, if I may be familiar, this is your third thread on the subject. May I suggest you get your Humminguru and then proceed from there? I do mean this in the friendliest way, as you have had the advice of all of us several times over. There's little point in flogging a dead record cleaner.

jjbeason14

Could it be because I was spinning old dirty vinyl which made the platter dirty/dusty?

Yes. And has @flemke noted, a new LP isn't necessarily clean.

An anti-static gun is almost a must-have for LP owners. Just dusting the LP with a brush can create a static charge. The Milty Zerostat is acceptable, but the Furutech DeStat III is imo better. Not cheap, however.

I never play NEW LPs w/o/cleaning them. I pull ultrasonic cleaned records & put them rite into a new MoFi sleave & when I pull them out to play, there’s dust from the air adheres rite to them. I just run the anti-static brush to them, before I drop the needle.

I just opened a brand new virgin/unopened LP and there's no static/pops...

What do you think?

I have, but i'm using the brush that came with the cartridge.

Should I buy one with liquid?

TIA

Humidity is unchanged since I bought the Technics 1500C which was recent.

I don't think that is the issue.

And as I mentioned I played the new lps several times (maybe 3 times each) with no static or pops.

New vinyl is not clean vinyl. The stylus creates static when you play the record as well. What is the humidity in your room?

I should mention that I initially played the new vinyl several times without static or pops...

HTH