I bought a bunch of no name RCA caps and also caps for my unused XLR ins and outs on eBay. At the very least, it keeps the unused inputs and outputs clean. Never heard a difference although my systems are dead quiet to begin with.
Capped off?
Good morning to the community! I am using RCA caps (from Cardas – don’t know if that makes a difference) on all my unused ports. Supposedly, they help eliminate crosstalk between the outputs and inputs. I’m really not sure if I can tell a difference, but they sure look cool!
Anybody else using these? If so, I would be interested in your thoughts. Thanks!
18 responses Add your response
A bit confused... I made "shorting" plugs years ago for unused RCA inputs on a couple of phono preamplifiers. I wired a small resistor from the RCA's center post to the RCA's outer band (as I was instructed to do). Forget the value, but it was small. There was a marked sonic improvement, though the (2) preamps were inexpensive battery powered stereo units that I ran as dual mono's for stereo (simple way of beefing up the power/battery supply). DeKay |
The new stuff like a Mcintosh C2500. there is no long runs of wire because its not point to point. Its all pretty much logic board, with really short runs, and RCAs and XLRs are soldered directly to the board. The "Shorting plugs" on Point to Point, Night and Day. You better, hook inside, to the outside of the RCA. Talk about clean it up. They are normally nickel, new stuff is gold. You can change that though, for the tweak guys.. I clean the heck out of the connections, with steel wool on a spinner, then, I treat them too. I use gold "CAPS" on my new stuff just for looks. It has NO purpose other than to keep the dust OUT, cover the RCA, and look good. PPT I thought it was Pin Point/point to point Termination, PPT caps, inside to outside. XLRs? Flipper caps, they do get dusty inside..without covers, though. Regards |
On the one hand I know a good deal about what and how. I know for example an otherwise perfectly ordinary plug can be transformed into something remarkable simply by putting a dab of goo on it. I know for example there is a reason for the little blob of gray goo on Synergistic Research Orange fuses, and it is for the same reason they tell you not to remove it. Also know something very much like that is going on with a lot of these things. So yes it is materials, and maybe a little design too. What materials? Aye, there's the rub. Shorting plugs, if that's all it is, then they do nothing. The outside of the RCA is ground, and ground is ground. The inside is hot. Look inside any component you will see one wire, the hot one, going to the input selector. All a shorting plug does is connect that short little bit of wire to ground. That's it. Minus the shorting plug that hot wire was just sitting there disconnected from anything. With the shorting plug its now connected to ground. I leave it to you to imagine how much difference there can be from one foot of one wire not connected to anything. As opposed to the magic goo. Which I guarantee you makes a huge difference. |
I don't know about Cardas, but if you were using the old PPT caps there would be no doubt. The reduction in noise, improvement in clarity, and image focus, is obvious and easy to hear. That's the problem with these things. Tweaks, I mean. Someone makes one that is truly outstanding. Everyone hears and says wow that is amazing. But then instead of buying the good stuff they decide to try something else. Which of course turns out to be crap. Or they use something that looks the same, and jump to the conclusion it is the same, and then in a Beamon size leap of logic conclude everything that looks like that is snake oil, to use this sites preferred vernacular. Get the PPT ones. If you can. Anything else, oh well. |
Shorting plugs are what is used for crosstalk. The plugs that you have are dust caps! This is what a shorting plug looks like! https://www.amazon.com/Viborg-Stopper-Plated-Copper-Protector/dp/B017DH76VS/ref=sr_1_3?dchild=1&... |