Tube Amp Repair

Thanks all for the help.  I wound up getting the unit to Vu Jade Audio in Boonton.  Peter and Karl were very responsive and obviously very knowledgeable.   I am expecting a easy fix as appears resister got fried.   

So sorry to see this happen.

I did a similar Performance dropping in a Kt88 without ceter pin, 1 pin off and smoke. Called Rogue audio tech dept, told me to look for obvious burnt parts.Found 3 resistors blown up, Replaced them myself and worked fine.

Sent it back to factory just for well being, Guess i fixed it fine as they found nothing wrong.

Id send it in to factory service..

Hello all of my friends and Audiogoners.

This is my first response on this fantastic forum.

Your request finally motivated me to come out of the closet, after almost three years of continuously deriving all sort of audio solutions and knowledge for my own need in my very late re-entry into this hobby.

At 67, and still building my sound room w/over $120 K in gear waiting in the boxes. Equi=Tech 5WQ wall cabinet currently in transit.

Anyway, with a such a lengthy introduction I just want to share my two cents regarding your dilemma.

I once contacted Bigkidz and ended up sending him my Cary 306 CD for a complete overhaul and an upgrade package. Couldn't be more happier with his professionalism and attention to detail. He has upgraded and improved the unit's sonic characteristics with over hundred new components for a very reasonable cost.

Good luck, and thank you all for educating me on this forum.

Chris.

Casper Yardley - Stereo Rehab in Chicago. Amazing tech.

A great tube engineer builder Radu Tarta is near theNY boarder in CT 

he does mods for most amps are not that well engineered 

and the primal luna tube sockets are very cheap , good ones are gold over Copper Teflon sockets that alone sonically a nice improvement .

I am in northern New Jersey  we can repair the amp no problem

We also build our own tube components so you can get a handle on what an upgrade would also sound like

Our Listening Room is in Boonton NJ

PM me

@rodman99999  huh?

I will call VAS, I also called Bristol Electronics in HoHoKus who used to be a primaluna repair.   I checked fuse on autobias and it is ok, so i have a feeling it is a resister or something under the socket.   groan

btw, does anyone know who might rent or loan an amp for a few months while waiting for fix?  

Where are you located, NJ, I'm in Plainfield, and drive 35 minutes to VAS in Cliffwood. I agree, Steve and his son Ray at VAS are terrific.

NJ Primaluna Dealers

https://woodbridgestereo.com/

@jasonbourne52 -

         Now, back to reality:

https://www.tubesforamps.com/broken-guide-pins

https://www.youtube.com/watch?v=LQG-dq38lFo

https://www.thegearpage.net/board/index.php?threads/are-tubes-with-broken-guide-pin-still-okay-to-use.735628/

https://www.decware.com/cgi-bin/yabb22/YaBB.pl?num=1588615343/3     

     There's a, "key" on the side of the, "guide pin" and that fits in a, "keyway", in the side of the, "guide pin hole", to be precise (correct nomenclature).      Folks still interchange the terms, however.              

     Push a couple bare wires and/or resistor leads together with a piece of plastic and let me know how that works out for you.

                       Have a nice (imaginary) day, "Jason Bourne".

I agree on the recommendation for Steve Leung. He often has a queue going but he does quality work and is a stand up guy. 

@rodman99999 : the OP broke the plastic guide key on the center of the base. 

     Did you remove the KT66's broken pin from the socket, before installing the EL34?

     I ask, because: a broken pin, if pushed through a tube socket, can often wreak havoc* on the other side.

     ie: There are wires and resistors that pass beneath the EVO300's, right channel sockets.

Steve Leung at VAS.