newbee
Responses from newbee
| How to fix my detailed, accurate but BRIGHT system I'm in the 'room/set up problem camp' and fundamentally agree with Johnnyb53. Appropriate acoustic 'treatment' would obviously be a great help but if you can't, you can't. But at least get an area rug on the floor between your chair and the speake... | |
| would it still I suspect that your LS3 had some DC at its outputs which caused the popping in/from your SS amp. Not unusual with tube/ss combos. This is relatively unusual with tubed amps as their transformers will not pass the DC. Some SS amps have built in pro... | |
| Cayin A50t biasing problem Larry, There is something in the bias circuitry that is common to all four pots. The meter! I'm not thinking it is broken, though it might be. What I'm thinking is that something between it and the pots is defective, for example the switch where y... | |
| Audio Research LS-7 LS7 upgrades suggestions Elevick has an excellent point about chasing too much money after mod's etc on a modest, 'budget'(for ARC), preamp.Apart from posting how much money you are willing to commit so you can get some more specific guidance, you might like to tell folks... | |
| Can even a Novice hear differences in Sound Qualit Lithojoe, If I were to read 100 of TVAD's posts I would certainly get some positive information I can use or, if nothing else, an intelligent POV. So I benefit from his existence. So I read his posts.Why should I read yours? | |
| Any point in adding tube preamp to SS integrated? IMHO, Re the probability of the addition of a pre-amp adding extra gain and creating a gain overload, consider that the VC on the CAP would attenuate the gain from the tube pre-amp just as it would any other source - the worst thing that would lik... | |
| Cayin A50t biasing problem Larry, are you saying that you have a 15 to 20ma reading regardless of the rotation of the bias pot(s)? Or that is the maximum reading available? Is there any difference in the reading between the 4 tubes/locations? You know it is entirely possibl... | |
| Any point in adding tube preamp to SS integrated? IMHO, you won't hear much 'tube magic', whatever that is, by adding a tube pre-amp ahead of the CAP101. What it will do, and it may be a good thing, is allow you to assert some influence on the tonal balance by using different tubes in the pre-amp... | |
| Cayin A50t biasing problem The pot travel of 3/4ths of a turn is not unusual. Three of my amps do this, including a Cayin. The bias curcuit not functioning at all is a different matter. I don't own a A50t so I don't know but is it possible the bias circuit is seperately fus... | |
| Can you lower gain requirements on tube amp? Well it sounded like 9db's! :-)Thanks Almarg for the info. I just never thought that db's and v's might share the same relationships. Makes sense though...........when I THINK about it. | |
| Best tubes 6922 for my Sonic Frontiers SFCD1 ? Changing tubes in a CDP should not change the 'soundstaging' ability of a CDP/DAC. Change the tone, change the clarity, perhaps even add a little 'air', but not make a 'huge' change. BTW, I think the Sovtek 6922, is at best only barely OK. It is c... | |
| Can you lower gain requirements on tube amp? Tholt, re DAC/CDP output voltage - I am presently running 4 digital sources. One with 2v, one with 2.2v, one with 3.5v and the latter varible at 2,4 & 6v. I have never measured the difference in db's at the speaker between each output level so... | |
| Can you lower gain requirements on tube amp? You can buy a different amp with lower input sensitivity. You can't change the Cary to get higher output other than the triode/UL option afforded. KT88's are high output tubes so rolling them won't make much or any difference.You can buy an active... | |
| Best Integrated Under $3000 FWIW I would not have, and still can't, respond to your thread intelligently. The is no universal best, so to respopnd to your question I would need 1) To have listened to the equipment you mentioned under controlled circumstances using identital ... | |
| DACs and reproduced sound I think the quoted portion of your post is vacuous. Every component in the chain processes the signal it recieves, digital or analogue. Each has an analogue output which has its own sound which is not going to be an exact copy of the input signal ... |