imhififan
Responses from imhififan
Tube replacement for Yaquin MC-10L Read the link below, it had everything you need to know about replacing tubes for your Yaquin MC-10L . https://community.klipsch.com/index.php?/topic/158463-tubes-for-yaqin-mc-10l-amp/ | |
Hooking up my JL sub Passing signal to my Marantz in Pure Direct mode cuts the signal to the subwoofer. Can I use a RCA Y splitter and pass one signal to Marantz and the other to JL audio? Maybe I misunderstand what you want to accomplish, since the DAC1 has both... | |
Preamp with HDMI inputs A hdmi audio extractor can pass-through hdmi and output SPDIF digital audio, so why limit yourself to preamp with hdmi input? https://www.amazon.com/AmazonBasics-Audio-Stereo-Extractor-Converter/dp/B07KRWYN4R/ref=asc_df_B07KRW... | |
Hooking up my JL sub Probably the easiest and best way would be to use either an electronic crossover, or just simply use a y adapter. Benchmark DAC 1 has both unbalanced and balanced outputs, the unbalanced rca output connect to Marantz AV7005, balanced ... | |
Hooking up my JL sub Why would you need a switcher? The sub would be hooked up all the time. It goes off by itself after no signal for about 15 minutes. Sorry I didn't make it clear, the switcher is for the subwoofer to select input from either the DAC1/LOC or Mar... | |
Hooking up my JL sub @ozzy , Yes, power amp with binding posts will need NL2 to Banana / Spade cable. https://benchmarkmedia.com/collections/all/products/benchmark-speaker-cable-nl2-to-banana-2-pole Probably the easiest and best way would be to use either an electro... | |
Hooking up my JL sub 1. If I connect using LOC most on the market are for car audio and says max RMS 50W. Is that a concern. Jensen Iso-Max SP-2SX is your answer, it use transformer isolated the speaker output to xlr output up to 750W! And you don’t have to worry any... | |
Integrated amp for Thiel 3.7's How about the Coda CSiB integrated: Preamplifier section is built on the Burr Brown PGA2310. It controls an analog attenuator with 99 steps with precision resistors. The balanced input is organized without OP amps - the signal from the XLR conne... | |
Preamp with HDMI inputs * any other things I'm not thinking of? hdmi audio extractor? | |
replacing tonearm question? the 9 inch Jelcos, which use a Linn mount and have a 214 pivot to spindle @hdm , thanks for the clarification, 240mm pivot to spindle is for 10" jelcos! | |
Help me select an integrated amp for Thiel CS3.6 speakers A new Bluesound Node 2i streamer/dac $500, a used Coda CSiB v3 integrated can be found below $3,000. I use this combo with thiel cs2.4 https://forum.audiogon.com/discussions/closest-to-pass-labs-int-250-or-x250-8 | |
replacing tonearm question? The pivot to spindle distance of Sumiko FT-3 is 221.7mm, and the Jelco 750 and 850 is 240mm. I think a new armboard is required unless you use a tonearm with same geometry (e.g. clearaudio) than you can use the existing armboard with some work. ht... | |
does anyone have a CM Labs 911 Schematic The 8mv from the output is due to the leakage current of the output capacitor, I think your amp is over 40 years old so best to replace those caps. The 911 is a single rail power supply, output capacitor coupled power amplifier, I don't think you ... | |
Leak Speaker Connector https://www.ebay.com/itm/High-Quality-2-pin-DIN-Male-Speaker-Plug-for-Sonab-Leak-and-B-O-speakers-/1... https://www.amazon.co.uk/electrosmart-Speaker-Loudspeaker-Cable-Connections/dp/B00512QE4I | |
Integrated stopped working Supply dead, fuse not blown - bad startup circuit (open startup resistors), open fusable resistors (due to shorted semiconductors), bad controller components. https://www.repairfaq.org/sam/smpsfaq.htm#smpstsps |