imhififan
Responses from imhififan
| Hooking up my JL sub @ozzy , Yes, power amp with binding posts will need NL2 to Banana / Spade cable. https://benchmarkmedia.com/collections/all/products/benchmark-speaker-cable-nl2-to-banana-2-pole Probably the easiest and best way would be to use either an electro... | |
| Hooking up my JL sub 1. If I connect using LOC most on the market are for car audio and says max RMS 50W. Is that a concern. Jensen Iso-Max SP-2SX is your answer, it use transformer isolated the speaker output to xlr output up to 750W! And you don’t have to worry any... | |
| Integrated amp for Thiel 3.7's How about the Coda CSiB integrated: Preamplifier section is built on the Burr Brown PGA2310. It controls an analog attenuator with 99 steps with precision resistors. The balanced input is organized without OP amps - the signal from the XLR conne... | |
| Preamp with HDMI inputs * any other things I'm not thinking of? hdmi audio extractor? | |
| replacing tonearm question? the 9 inch Jelcos, which use a Linn mount and have a 214 pivot to spindle @hdm , thanks for the clarification, 240mm pivot to spindle is for 10" jelcos! | |
| Help me select an integrated amp for Thiel CS3.6 speakers A new Bluesound Node 2i streamer/dac $500, a used Coda CSiB v3 integrated can be found below $3,000. I use this combo with thiel cs2.4 https://forum.audiogon.com/discussions/closest-to-pass-labs-int-250-or-x250-8 | |
| replacing tonearm question? The pivot to spindle distance of Sumiko FT-3 is 221.7mm, and the Jelco 750 and 850 is 240mm. I think a new armboard is required unless you use a tonearm with same geometry (e.g. clearaudio) than you can use the existing armboard with some work. ht... | |
| does anyone have a CM Labs 911 Schematic The 8mv from the output is due to the leakage current of the output capacitor, I think your amp is over 40 years old so best to replace those caps. The 911 is a single rail power supply, output capacitor coupled power amplifier, I don't think you ... | |
| Leak Speaker Connector https://www.ebay.com/itm/High-Quality-2-pin-DIN-Male-Speaker-Plug-for-Sonab-Leak-and-B-O-speakers-/1... https://www.amazon.co.uk/electrosmart-Speaker-Loudspeaker-Cable-Connections/dp/B00512QE4I | |
| Integrated stopped working Supply dead, fuse not blown - bad startup circuit (open startup resistors), open fusable resistors (due to shorted semiconductors), bad controller components. https://www.repairfaq.org/sam/smpsfaq.htm#smpstsps | |
| does anyone have a CM Labs 911 Schematic unit works OK but for the 2v dc on both sides of the speaker outputs that I cant adj out Did you connect a load to the amp output to do the measurement? The 911 has a output capacitor, if no load connected, it will show some DC reading! also t... | |
| does anyone have a CM Labs 911 Schematic If you’re a forum member of either diyaudio.com or audiokarma.org, you can contact him through those site. His last post at audiokarma was Aug 2018, at diyaudio his last post was May 2008, so the best site to contact him will be audiokarma: https:... | |
| does anyone have a CM Labs 911 Schematic The designer of CM Labs 911, Wayne Chou, is a active member of audiokarma.org, maybe he can give you some help. https://audiokarma.org/forums/index.php?threads/cm-labs-preamp.315531/ There's a downloadable online service menu for $10.95 https:/... | |
| Does anyone know if Bluesound Node 2i Streamer/Dac is being updated soon. I found my old Samsung 10" tablet works much better than my phone. | |
| External Balance Control Why not? You'll never know... |