128x128

imhififan

Responses from imhififan

How to connect an equalizer to an integrated amp.
You can connect the EQ to preout2 and main-in, subwoofer to preout1. The EQ will only effective to your main speakers, no effect to the subwoofer. If you want the EQ control subwoofer as well, a pair of ’Y’ connector will be needed. https://encryp... 
Accuphase DP-560
You need to cut open or desolder the jumper wire on J1 and solder a jumper wire to J2. 
Eq to pre amp
 If your phono stage comes with both xlr and rca outputs, you can connect the rca output to mc700 analog input for EQing, connect xlr output to your esoteric c03 balanced input if EQ is not in use. 
Eq to pre amp
@rohanraman, maybe you can utilize the built in programable parametric equalizers comes with your emotiva mc-700 instead.  
cec tl-5 oem usa version
From the inside view of tl-5, voltage conversion can be done by jumper setting. https://www.hifishock.org/wp-content/uploads/electronics/cec/source/cd-player/cd-transport/tl5-cec-1...  
How do I connect my emotiva mc700 surround sound proc to preamp
If that is the case, you can connect the emotiva mc700 LF and RF output channels to emotiva mc700 ANY of the three RCA inputs, set the emotiva mc700 volume to maximum, or to the level matching other sources, and use the esoteric c03 volum... 
How do I connect my emotiva mc700 surround sound proc to preamp
Sorry, I just revised my response. 
How do I connect my emotiva mc700 surround sound proc to preamp
Whats the difference between using THRU and normal? If the RCA3 is in normal mode, the preamp volume control still active. When RCA3 in signal thru mode, the preamp volume control will be disabled, you will using the emotiva mc700 to control volum... 
How to connect monoblocks to a single REL sub with ONE RCA input
Regarding your recent question about the device suggested by @imhififan , when I looked at the links he provided what particularly gave me a fair amount of confidence was the statement on the packaging that can be seen in one of the photos, th... 
How do I connect my emotiva mc700 surround sound proc to preamp
Connect the emotiva mc700 LF and RF outputs to esoteric c03 RCA 3/Signal-Thru inputs. On the esoteric c03 setup menu configure the RCA3 input to SIGNAL THRU. https://www.manualslib.com/manual/532689/Teac-Esoteric-C-03.html?page=11#manual 
How to connect monoblocks to a single REL sub with ONE RCA input
An alternative is that I get a Y cable that will bring two RCA outputs from my Preamp into the single RCA input on the REL? Unless there’s a resistor in series to the preamp outputs, using a ’Y’ cable that bring two RCA outputs from your Preamp in... 
Amps and Kimber 12tc. Big amps and room temperature.
May I ask what speakers are connected to the Bryston 14b3?  
Voltage conversion of Accuphase A-48
I have an old voltage selection table may worked on A-48 100V - 1= none 2= white+gray 3= yellow 4= brown+red 5= orange 120V - 1= none 2= white+gray 3= brown 4= yellow+orange 5= red 220V - 1= brown 2= white 3= yellow+gray 4= red 5= orange 240V - 1=... 
Accuphase DP-560
Sorry I have no experience with DP-560, on the DP-550 Accuphase offer three input voltage selection: Main transformer J1 = 100v J2 = 120v J3 = 220-240v Standby transformer J4 = 100-120v J5 = 220-240v You can simply measure the DC resistance of t... 
How to connect monoblocks to a single REL sub with ONE RCA input
Or is there another alternative? You can connect your preamp  second main out to a  Stereo to mono signal converter and connect one of the converter mono output to the REL 328 low level input. This converter utilizes an independent 1:1 ratio au...