imhififan
Responses from imhififan
I have a weird buzz issue; can you help me solve the problem? Just out of curiosity, did you have CODA bump up the amount of Class A watts? I wish I could, but I need most of the class B power to feed the power hungry Thiel. | |
I have a weird buzz issue; can you help me solve the problem? I also like to add that something like a cold solder joint can caused intermittent problem like this, that explain why the amp was dead quiet when plugged into the mains at audio store and the manufacturer. | |
I have a weird buzz issue; can you help me solve the problem? I have a CODA CSiB v3 integrated plugged directly to the wall, without any shorting plug installed, no buzz, hum or any kind of noise while bias “ON” at any selected input. I think the last thing you can try is to turn off all circuit breaker exce... | |
Need Help! Couple ideas: https://www.audioadvisor.com/prodinfo.asp?number=PGVUXAS https://www.homedepot.com/p/Noble-House-Bartlet-39-37-Clear-TV-Stand-Fits-39-in-TV-7628/307889422 Put the turntable on top and the amp underneath, for the homedepot one, just s... | |
Need preamp recommendation Sell the Proceed and up the budget to 8.5k, go for a Mark Levinson 5805 integrated with phono and DAC built in. | |
share 2 CH speakers with HT set up or use separate speakers for front end of a 7.2 HT? Since you already setup and calibrated the Lyngdorf for stereo playback, all you need to do is add HT bypass to it: 1. To setup HT bypass, disconnect front L/R speakers on the Denon and using a pair of interconnect cable connect the Denon front... | |
Set-up with two subs and an integrated amp This is what you need: https://www.crutchfield.com/S-BZsGXIya5Pj/p_543ADP12/Russound-ADP-1-2-Speaker-level-to-Line-level-Ad... | |
Aragon 2004 Wanted to add a pic but don’t see a way of doing it here. Can we not post pics? Go to Virtual Systems page, select ’Create System’, you can upload pictures to your system... https://systems.audiogon.com/systems/1986#&gid=1&pid=1 | |
I have a weird buzz issue; can you help me solve the problem? If buzz on both channel, I suspect the CSiB power supply section or internal grounding has issue, my suggestion is send it to a tech to diagnose. | |
share 2 CH speakers with HT set up or use separate speakers for front end of a 7.2 HT? My suggestion is go for HT bypass, what you need is a pair of interconnect cable. | |
Vandersteen 2c vs Thiel CS2 @mike_in_nc Thanks for your quick response, I've used Jantzen 0.33mH foil coil in series to the coax xover to tame sibilance on bright recordings. | |
Vandersteen 2c vs Thiel CS2 Thiels have very pronounced treble. That gives them great imaging, air, and soundstaging, but can make them hard to listen to. I finally built a low-pass filter to tame them. @mike_in_nc Can you kindly provide details of the low-pass filter? | |
Voltage conversion of Accuphase A-48 The purpose of voltage conversion from 100v to 120v is to give the amplifier circuitry correct operation voltages.https://1.bp.blogspot.com/-Yn62ubWAJB8/XZBPQoN1Z8I/AAAAAAADXY8/Fa5bof2bzGs7ECGh9lAp1qj-ddhNSw6dwCLcB... To measure voltages across l... | |
Does anyone collect something else other than music. Schematics from the web. | |
Krell KSA-200S Power Cable Use an IEC C13 to IEC C14 Adapter may workhttps://www.amazon.com/AudioQuest-IEC901-Female-Right-Angle-Adapter/dp/B000UJ2TEQ https://www.amazon.com/ACA1014-Adapter-Certification-Standard-Connector/dp/B07DCVFVT4/ref=sr_1_1_ssp...= |