imhififan
Responses from imhififan
| Voltage conversion of Accuphase E-650 Yes, Fill the empty holes in K3 and K4, it will increase the mechanical strength of the PCB especially holes with through hole plating. Hope this helps | |
| Voltage conversion of Accuphase E-650 @quanghuy147 To convert the voltage from 100V to 120V, Move K3 to K5 and K4 to K6 position. Voltage conversion on E-600, E-650 and E-800 basically similar, first row of connections for 100V, second row for 120V and third row for 220/240V. For... | |
| Crossover help? These are the photo OP posted on his system page, Seems like a simple two ways 2nd order xover with total 6 components. The 3rd photo I believe is the original xover. Based on the picture, I draw out the schematic: Without tweeter con... | |
| Accuphase E650 XLR Input issues @paradis Could be bad contacts on the "BALANCED CONNECTION" selector, switch it a few times to clean the contacts and see if the problem go away. | |
| Crossover help? what is the brand and model of your speaker? To post pictures, go to https://systems.audiogon.com/ Click the "Create system" on the top menu bar, then type in a system name and you can start add images to it. | |
| When choosing new Speakers, what matters most to you? Size is the single most important thing! You can't put Magnepan 20.7 in a 10x12x8 room to sound right. I have small monitors for my small office and big floorstander in my listening room. | |
| Does anybody make... I think what you want is a "Audio Distribution Amplifier", which connect among the preamp stereo outputs to the inputs of power amps. Rolls-DA134-4-Channel-Distribution-Amplifier | |
| Crossover help? I do get a bleep from both terminals so assume thats the parallel resistor. I think you wired the high pass crossover wrong. If there’s a parallel resistor, it should be after the capacitor and connect across the tweeter +/- terminal. If the p... | |
| How to tame a bright system? If possible, please help to focus on the cable rather than the other components. Sorry, IMO, you pairing bright sounding amplifier to bright sounding speakers, my suggestion is save your money on cable and go try some speakers with soft-dome t... | |
| Strange Problem: Philips 867 Turntable ...Please read Same explanation: The power amplifier switch–on surge sent a pulse signal triggered the table to turn on. IF plugged in the turntable directly into wall outlet and touch the 33 or 45 speed panel still can't turn on the table, your table is not w... | |
| Strange Problem: Philips 867 Turntable ...Please read If plugged in the turntable directly into wall outlet and touch the 33 or 45 speed panel still can't turn on the table, the only explanation I can think of is when switch on the RGR Pre-amp, its switch contact arced and sent a pulse signal trigger... | |
| Position of speaker cables and irregular behavior If you move your sitting position can you get the center image? | |
| Hum on inputs of new Rogue Sphinx v3 If you disconnect the TV DAC from the preamp input and the noise/hum disappear, try a Ground Loop Isolator between DAC output and preamp input may help. https://www.amazon.com/InstallGear-Ground-Isolator-Noise-Filter/dp/B077Y5DLBB | |
| Convert Accuphase C27 from 100V to 120V Congrats! Thanks for posting the result. Please confirm if the 120V wire configuration as following: Black to Black Yellow to Yellow > Blue soldered wire Brown to Brown White to White > white soldered wire This may helps other membe... | |
| Using SUBWOOFERS internal crossover... When the signal is routed through the subwoofer, the piano moves TO THE LEFT... This is not a problem usually. It sounds like there might be something wrong with the sub crossover. I agree with @russ69, seems like the high pass crossover was... |