imhififan
Responses from imhififan
| Subwoofer Connection: Speaker Level Amp to Line Level on Sub? from speaker level on the amp to line in on the sub using an adapter? It should be fine if you connect the sub line level rca inputs to your amp speaker blinding posts via a LOC (line output converter). https://images.crutchfieldonline.com/Image... | |
| Bi Wiring Speakers from Luxman L-509X The low and high pass filters means the multiple drivers are not not seen in parallel by the amplifier. They are seen as separate entities. For a better view to understand this, please see my post here:https://speakermakersjourney.blogspot.com/2... | |
| Bi Wiring Speakers from Luxman L-509X The amplifier sees the same speaker load either way. @erik_squires +1 So highs @ 8 ohmslows @ 8 ohms- to -, and + to + = 4 ohms No!!! The high pass crossover has high impedance at low frequencies and the low pass crossover has high impedance... | |
| Diy dc blocker, net filter, auto on, soft start, ... solution using boards DC Blocker & EMI/RFI/Common Mode Filter https://www.ebay.com/itm/133122929719 Not sure if I need a soft start too as all my amps will be immediately on? Would I need other boards as well to "improve" my current? You can use a time delay rela... | |
| Jorma no.3 cut a small piece and make jumpers One alternative is solder both high and low internal wires onto one set of speaker blinding posts to eliminate the need of jumpers. | |
| What is a cost effective way to level match, for comparing different hifi components? Acknowledging the importance of level matching when comparing source components is a sign of a good listener. +1 @tvad If you don’t understand the importance of level matching when comparing source components, you need a new hobby! | |
| Spindle-To-Pivot Distance Install a slidable arm base, slide to 250mm to play a record, slide to 240mm for good looking. https://i.ebayimg.com/images/g/hz4AAOSwuhheVlOd/s-l1600.jpg | |
| Bi-amping versus Bridging for NAD S200's bobandtorey The bi-amp method you’re using is horizontal passive bi-amping, since you're using two identical power amplifier, you also can try vertical passive bi-amp by using both channels of each power amp to drive each of the speaker highs/Mid ... | |
| Pioneer SX-850 Transformer Secondary Output Voltage Although 20.6V on each green wire and 48.4V on each orange wire seems a little high according to the schematics of service manual, I think it's OK since those windings connect to voltage regulator circuitry after rectifier. The 33.1V on each red... | |
| list of integrated with pre-out AND main-in Accuphase, Luxman, McIntosh. | |
| Speaker brands known to use first class internal components Are there brands that can be purchased with "confidence" (pun intended) that are sure to use top notch crossovers, wiring and speaker cable terminals? https://www.tidal-audio.com/technology-crossover/ https://www.tidal-audio.com/technology-dri... | |
| Identify older Paradigm speakers I think that is the Paradigms Model 7 from the early 80s https://img.canuckaudiomart.com/uploads/large/2313127-c1729884-paradigm-7-bookshelf-speakers.jpg https://img.canuckaudiomart.com/uploads/large/2313126-298ac5c3-paradigm-7-bookshelf-speake... | |
| Cary V-12 blowing capacitors The original power transformer that was in it had a direct short and could have caused the UCC’s to stress. I thought the opposite, shorted filtering caps stress upstream power supply components ( rectifier diodes, power transformer and fuse ) ... | |
| Cary V-12 blowing capacitors I asked him why he thinks the black UCC would explode and he said the only way for them to explode is if they were wired with reverse polarity. Or if they were wired with shorted rectifier diodes. | |
| Perfect match for ATC speakers If you like ATC, try their active... perfect match amplification! http://atcloudspeakers.co.uk/professional/loudspeakers/scm20asl-pro/ |