imhififan
Responses from imhififan
| Klyne Preamps This is a Klyne 7PX manual http://www.techtrader.ch/auction/2016/03/Klyne-7-PX_B-3.5.3-manual.pdfHope it help | |
| Anyone Used REW-Room EQ Wizard? https://www.roomeqwizard.com/help/help_en-GB/html/gettingstarted.html#connectionshttps://www.roomeqwizard.com/help/help_en-GB/html/makingmeasurements.html | |
| How do I remove the woofer from ads 300 speaker? Can you remove the tweeter to access to the back of the woofer? | |
| Klyne 7PX question http://www.techtrader.ch/auction/2016/03/Klyne-7-PX_B-3.5.3-manual.pdf | |
| Electrocompaniet ECI-5 MkII click/noise in speakers when turning on/off I don't own this amp, but I'd found this info on their website: ECI-5 MK II also has a new and improved overload detection system that allows us to remove the output relay. Hence the output stage is connected directly to the speaker with no rela... | |
| Marantz 1200 vs Marantz 1200b [PDF]Marantz-1200-Service-Manual-1 - Vintage Hifi[PDF]Marantz-1200-Service-Manual-2 - Vintage HifiThe service manual contains all the info | |
| Krell KRC3 preamp can you please answer the second part of my question about additional RCA connections from MX135 to my amp? Sorry I don't understand your question, can you more specific? If you want stereo playback through MX135, just select S3 input on KRC3;fo... | |
| Krell KRC3 preamp My suggestion of using a Goldpoint SW4 is easier to A/B comparing two preamps. If you decided the KRC3 is better for stereo playback, then set the S3 to HT passthrough will be the best way for connection. you can use the KRC remote contro... | |
| Krell KRC3 preamp If your KRC3 had configured the S3 as Proc, then you can use this input as a HT passthrough and connect it to MX135 FR/FL output,the connection as below: the "stereo audio out" on the oppo 205 connect to S1 on KRC3the "5.1CH audio out on the oppo... | |
| Krell KRC3 preamp @ei001hYou need to remove the top cover of the Krc3, look for a red dip switches labeled "Input configure" and set the S3 to Proc. position. | |
| Krell KRC3 preamp My suggestion:the "stereo audio out" on the oppo 205 connect to KRC3the "5.1CH audio out on the oppo 205 connect to MX135use a Goldpoint SW4 Main out connect to KAV500 FR and FL inputhttp://www.goldpt.com/sw4.htmlKRC3 output to Goldpoint SW4 Li... | |
| sub to my Mcintosh c40... After a quick look at the McIntosh C40 Owner's Manual,I believe you can connect the kilpsch rsw 10 Line input to either switched output 1or 2 of the C40 and switch on the speaker 1 or 2 accordingly, | |
| Two amps to one speaker Here’s a very recent thread with some suggestions https://forum.audiogon.com/discussions/a-rookie-question-re-two- amps-one-pair-of-speakers The above link was only good for switching between two solid-state amplifier, to switch between a tube a... | |
| Suggestions for active crossover setup please. An inexpensive example: Rolls SX45 Stereo Two-Way Mini Crossover w/Sub Output | |
| Mid Range Remote Volume Control An Infrared Remote Control wouldn't work!What you need is a RF Remote Control to provide +Voltage or -Voltage to a Motorized Volume Pot. https://www.amazon.com/Channel-Wireless-Control-Receiver-Momentary/dp/B00FFW1DI6http://www.ebay.com/itm/10pc... |