imhififan
Responses from imhififan
| Job amps: Suck? I’m asking about this because I’m entering the market soon for an upgrade amp/integrated. Please help us to help you, can you please list your existing system: source, amplification and speakers? | |
| Soulution preamp DC-offset protection While waiting for the manufacturer's reply, maybe try the player and preamp with factory default setting. | |
| Soulution preamp DC-offset protection What is the CD player/DAC? | |
| Trying to find a name I bet it’s Wells Audio. +1http://www.wellsaudio.com/#home | |
| Bi-amp through receiver vs pre out to 2 channel for fronts on the HT receiver setup menu you need to select front R/L speakers to "Large" and No subwoofer. On this setup the HT receiver will send the LFE signal to front speakers.The downside of this setup is those small front speakers will operate at fu... | |
| Bi-amp through receiver vs pre out to 2 channel for fronts You can connect the integrated amp pre-out to the subwoofer line in , use the subwoofer's internal low pass filter set to 80Hz to begin with, on the HT receiver setup menu you need to select front R/L speakers to "Large" and No subwoofer. | |
| Jeff Rowland Design Group Measurements :Dan D’Agostino Momentum monoblock power amplifier The unweighted, wideband signal/noise ratio, ref. 2.83V into 8 ohms and taken with the input shorted, was a good 77.2dB, this improving to 78.1dB when the measurement was restricted... | |
| Display case for cartridges https://caseelegance.com/collections/watch-cases/products/solid-light-wood-watch-box-organizer-with-...https://www.amazon.com/SAVORI-Lacquer-Organizer-Superior-Removable/dp/B078SRW2Q8/ref=pd_sbs_241_42?_... | |
| McIntosh / Audio Research 12V remote start jack If a 3.5mm stereo cable can't control the front panel meter illumination, maybe you can add a 3.5mm Mono Plug to 3.5mm Stereo Jack Adaptor on REF3 12v trigger output.https://www.amazon.com/Monoprice-107128-Stereo-Adaptor-Plated/dp/B002N1XMPO... | |
| Preamp for Burmester power amp Burmester Preamp for Burmester power amp :) | |
| Help! Unplug the power cord, unscrew the 4 screw on top to open the top plate and you can clearly see the fuse on PCB, be caution the capacitors may still charged! http://img.ukaudiomart.com/uploads/large/1858817-emerald-physics-1002se-amplifier.jpg | |
| Connecting a Bryston 12B http://www.bryston.com/PDF/Manuals/11B_12B_MANUAL.pdf | |
| Bi-amp through receiver vs pre out to 2 channel for fronts what are thoughts on buying an amp first to run from my Elite receiver, and then buying a pre amp with HT passthrough in the future to stick between them? Wonderful idea! it made subwoofer connection easier too.https://forum.audiogon.com/disc... | |
| Need Help with my Proceed AMP3 https://3.bp.blogspot.com/-yv16P50tZSk/UrRIUilHwII/AAAAAAAACAM/vcM3k-CY5SE/s1600/IMG_0350.jpglook for any burnt resistor, shorted transistor or leaked cap, also check the relay contact on this circuit board. | |
| spade lugs won't fit I use pin connector as a adapter and put plastic sheet between two connector for insulation.https://ae01.alicdn.com/kf/HTB1raZuX9_I8KJjy0Foq6yFnVXaq/2pcs-PIN-Plug-24K-Gold-Copper-Speaker-Pin-2...Or you can use a standoffhttps://www.amazon.com/Stan... |