Does anyone know how to convert voltage of Accuphase E-5000 100v to 110/120v? Or does anyone provide information on voltage conversion table of Accuphase E-5000?
what do you mean convert? are you referring to different countries voltages? Japan @ 100v, NA @ 115v and Europe etc. @ 220v.
you should note Japan’s voltage and NA’s voltage are close but not close enough to run a 100v Japan model on NA’s 115v. you would need a voltage step down for the Japan model and step up transformer for the 220v assuming your in NA 115v.
I’m not sure about your specific amp and if it has a switch on the back to change supply voltages, your manual would have that as for internal changes again your manual should have that if available. chances are the manufacturer only puts the transformer in the chassis for the voltage in the country being sold, if its not switchable on the back.
If your trying to run an amp made for another countries voltage you will need a step up or step down transformer. quality ones are available online. Make sure you get one that exceeds the rated max power draw of the amp plugged into it. this can be found on the back in watts. potted transformers in the step up/down transformer would be the best but rarer.
For example a standard 15amp 115v outlet in a NA house has a max draw of approx. 1500watts. your amps max wattage 570w draw then buy a step up or step down transformer that is at least 25% larger then the max. you should buy a 750w-1000w transformer probably the 1000w as that’s a standard size and will give enough head room to never be a concern.
from the E5000 manual below:
Power requirements 120 V, 220 V, 230 V AC (voltage as indicated on rear panel) 50 / 60 Hz
Power Consumption Idle 98 W In accordance with IEC 60065 570 W, Stand-by 0.3 W
You need to be aware that Accuphase only offers parts and service support for products purchased in the country in which you live.If it needs repairs you will need to send it back to the country in which it was sold.
Thank you very much for the information. In case I actually do the work for voltage conversion, I might ask again in details. Thank you again in advance for your help.
Meanwhile, I am going to try to convert voltage of the Accuphase E-700 to 120V. Voltage conversion of the E-700 is the same as the E-650? It would be very much appreciated if you would provide information on how to convert voltage.
Sorry, I don't have voltage conversion information for the E-700, I'm guessing it's probably similar to the E-5000. However, if you could post some pictures of the power supply board, maybe we can figure it out.
To convert the main power transformer primary winding voltage from 100VAC to 120VAC, move connector K1 to K2 and K4 to K5.
However, there is an auxiliary transformer in the upper right corner of your third picture, which supplies power to the standby circuit. It needs to be changed to 120VAC, or use a resistor connected in series to drop 20V so that the existing transformer can be used.
Thank you for providing information. Regarding the auxiliary transformer, I in case the existing transformer is used, how should I use a resister connected in series to drop 20V?
I will appreciate if you would provide more information.
Thank you very much for providing information. Before receiving your message, I have done modification of circuit of the auxiliary transformer. Actually, a person with electronic and soldering skill has done.
According to him, he inserted a resister : 2000 Ohm/2.5W (10kOhm/0.5W x 5 parallel) in series to the fuse and confirmed that the voltage at the DC plus line is 20% less from the original circuitry while power SW is ON.
Although U.S. mains voltage is rated at 120VAC ± 5%, in some cases household outlets may have voltages as low as 104VAC.
My suggestion would be to power the amplifier with a variac set to 104VAC and see what the highest resistance in series is allowed to turn the amplifier on, if 2kΩ works then it's no problem.
Thank you very much for your quick response. I turned the amplifier on with nearly 100VAC and confirmed 2kΩ works.
I have successfully converted the E-700 from 100v to 120v thanks to your great help. Thank you very much again.
Meanwhile, also I have started discussions about voltage conversion of the E-4000 and the DP-450. I will appreciate very much if you would post information on them. I am ready to post some pictures of the power supply board.
I have successfully converted the E-700 from 100v to 120v
Great! You're most welcome, glad I could help.
I turned the amplifier on with nearly 100VAC and confirmed 2kΩ works... Meanwhile, also I have started discussions about voltage conversion of the E-4000 and the DP-450.
You can use the same method to convert the E-4000 and E-5000 from 100V to 120V.
BTW, if you could post some pictures of the DP-450, maybe we could figure out how to do the voltage conversion.
Thank you very much for your providing information on the voltage conversion. I will need to remove the PCB to take photos. I will post an image of the front and back of that PCB as soon as I take photos for it.
Sorry, I have no experience with voltage conversion with the Accuphase C-47 and PS-1250 either.
I'd love to know how to do that though! If you could provide some close-up pictures of both sides of the power supply board in your threads, maybe we can figure it out.
Sorry, I have no experience with voltage conversion with the Accuphase C-47 and PS-1250 either.
I'd love to know how to do that though! If you could provide some close-up pictures of both sides of the power supply board in your threads, maybe we can figure it out.
Regarding PS-1250, do you think it is possible to convert voltage to 120V without replacing the main transformer?
Converting Accuphase amps from 100v to 120v is not straightforward as the above discussion illustrates. You can never be sure that it was done correctly or to Accuphase standards ("you can use a 680Ω 3W resistor to replace fuse F1"). The above discussion does not inspire confidence, and these units could be a fire hazard.
Given the range of units that have been mentioned above for conversion (E-5000, E-700, E-4000, DP-450, C-47, PS-1250, C-3900, A-300 - and C-2300 in a previous thread) this sounds more like a business venture as opposed to someone putting together a personal system. These units could appear on the secondary market. There may be some attempts at stencilling on the rear panel to hide the conversion and make them look like authentic 120v units.
I would urge all Audiogon members to be very wary of buying units that have been converted and relabeled and to carefully investigate the provenance of used units.
Converting Accuphase amps from 100v to 120v is not straightforward as the above discussion illustrates. You can never be sure that it was done correctly or to Accuphase standards ("you can use a 680Ω 3W resistor to replace fuse F1"). The above discussion does not inspire confidence, and these units could be a fire hazard.
Thanks for pointing it out! I should have been more specific.
You can use a 680Ω 3W resistor to replace fuse F1.
The vishay resistor that I recommended is a fusible resistor, it will blow out like a fuse in the event of a short circuit, protecting the circuit from damage and fire.
Fusible resistors are used as safety devices to prevent electrical fires and other damage caused by excessive current being applied at once. They can be found in household appliances like washing machines and microwaves, as well as electronic devices like stereos.
A fusible resistor performs dual functions. Once the power supply is exceeded, then it works like a resistor limiting current. Similarly, once the rating of power is exceeded, then it works as a fuse in the circuit to defend different components within the circuit from the surplus current.
Anyway, my intention is just to help those who have an Accuphase with Japan voltage and want to convert it to 120V or 220/240V, I don’t gain any financial interest from anyone.
Anyway, my intention is just to help those who have an Accuphase with Japan voltage and want to convert it to 120V or 220/240V, I don’t gain any financial interest from anyone
Your comments are correct and very persuasive. I am not interested in running business about any audio gears, but I am very interested in quality of sound.
I look forward to your posting comments in the future.
You must have a verified phone number and physical address in order to post in the Audiogon Forums. Please return to Audiogon.com and complete this step. If you have any questions please contact Support.
