2. cables
  3. 156991-88

support for heavy PC?

Just installed a new Synergistic Blue UEF HC pc and have a noticeable difference in the sound presentation from my Classe integrated amp but, the weight of the cord is the issue for me. The cord is 7' long to the outlet and the outlet is 13.5" above the floor level and is inserted into an Oyaide SWO GX+ outlet (the amp resides in a Sanus stand and is 25" H at the IEC input). With the weight of the cord once inserted in the outlet doesn't stay fully inserted unless supported in some way in order to stay as such. Has others found a solution to this type of problem, cable risers aren't tall enough to help me out with this and I don't want to spend a mint but, would like it to be able to have wf acceptance too. Has anyone else run into this type of problem and how were you able to solve it? Non foolish responces would be most helpful.
rsjm80
13 responses Add your response
bar81
791 posts
 
@rsjm80 

This will do what you want with added performance as a bonus (or so I'm told - I have one on hand but haven't had a chance to try it yet):

Furutech NCF Booster Brace
http://www.furutech.com/2019/09/13/18748/

The booster brace uses adhesive pads to stay attached to the outlet (skip to 1:09 to see the wall outlet install):
https://youtu.be/K93WnnjDcfQ

petg60
1,486 posts
 
Hi,
Furutech NCF boosters.and extension shafts.
steakster
1,878 posts
 
" . . .and rotate the outlet 180 degrees so the ground pin is at the top. That way the ground pin handles all the weight of the cable . . . "

Did the above. Bad idea. The ground pin on the heavy power cable bent - and then broke off. A support underneath is much better. Home Depot has saws available for customer use next to their remnant wood bin. Cheap & easy.
rsjm80 OP
207 posts
 
jwpstayman, Thanks for reminding me I could do that! I turned the outlets 180 degrees yesterday (finally) and it works great. Thanks also to everyone that recommended ideas for a solution to me, I took all in consideration and had even investigated cost and design ideas.
The New Synergistic UEF Blue HC cord has made a marked difference in every every CD I've played, so all I can say is wow!
lak's avatar
Ag insider logo xs@2x
lak
4,626 posts
 
Using any type of hardwood you can make an I beam at the height you need to support your AC cable at the wall.
rsjm80 OP
207 posts
 
Thanks to all for your responds and ideas hadn't thought of a couple ways to do this but the info you've given sure helps as I need to get a support in the range of 14' tall but rotating the outlet 180 might work and if that doesn't then... you've helped with alternate ides. Thank You all for the useful suggestions.
Post removed 
millercarbon's avatar
millercarbon
12,531 posts
 
All things that will help to hold the plug in. The only one that will do that AND make the setup look better AND sound better all at the same time is to support the cables on risers. Risers are simple and cheap to make. Mine are MDF shop scrap but you could use wooden dowel with an acrylic base to look real nice. Also the ceramic insulators do not have to be generic white like mine there's a huge variety on eBay all of them with a large screw hole underneath to accept a riser, and the whole thing can be painted any color you, excuse me your wife (the boss) likes. 

Speaking of which since it seems this is all up to her why not just put her on? Cut out the middle man, er, party.
Post removed 
jwpstayman
399 posts
 
RSJM80- here is a NO-cost way to accomplish what you need to do.  Shut off the breaker for the outlet, take the cover off and rotate the outlet 180 degrees so the ground pin is at the top.  That way the ground pin handles all the weight of the cable and the hot and neutral will stay connected in the outlet.  Of course, this only works with US outlets, but it is within electrical code and is VERY effective.
tom6897's avatar
tom6897
1,484 posts
 
I really wish that AudiogoN would allow the posting of pictures without having to send people to another site for image uploading.

@rsjm80 try to imagine loosening the outlet screw just enough to slip the end of a leather shoe string that has been tied like a slip not that will go around the cable where it meets the male/female receptacle. Cut to length so that there is enough tension on the cable to keep it level with the hole in the outlet and not sag. I am sure that if you remove the outlet cover you can find several places to secure one end and let the shoe string come over the top of the outlet and uphold the cable. Heavy gauge fishing line would work as well and have high WAF, also non conductive.
samuel03's avatar
samuel03
40 posts
 
I use stacks of paper cups upside down in the strategic spots.
millercarbon's avatar
millercarbon
12,531 posts
 
https://systems.audiogon.com/systems/8367
Log in to respond
More to discover
80x80
Nordost Red Dawn
80x80
ANTICABLES Level 3.1 Reference Series
USB Digital Interconnect
80x80
Avanti Audio Vivace Interconnects