HT amp for my father - advice please

Outlaw Audio has the Marantz SR5005 for $500 with free shipping. It is a 7.1 receiver with zone 2, pre-outs, 100 watts per channel. I think you might still need to add external amps for best performance, but the Marantz might be a start.

When you say $500 amp, do you mean a home theater receiver? If so, using its amps it is not going to do justice to the Concertino, although if he is just listening to mp3 music, it may not matter a lot. If these are the old Concertino bookshelves, they sold for $1K each. The new Domus floorstanders are even more.

If you just want an amp, then the ATI 150x is in your price range and has plenty of power.

Following on to what Mceljo said, in oder to drive the HT and the whole whole house from one receiver you need a 5.1/7.1 receiver with zone 2 capabilities. One with pre-outs will allow you to incorporate externals amps for the LRC and whole house.

One approach would be a receiver with pre-outs and zone 2 capabilities and an ATI 1505 amp. You could use 3 of the 5 channels on the ATI for LRC and 2 for whole house. The LRC would use the pre-outs of the receiver and the whole house would use zone 2 pre-outs. The surround speakers could then be driven from the receiver, as they are not as critical. Zone 2 lets you play whole house music separately from the HTsetup.

Hopefully the 3 sets of whole house speakers have impedence matching volume controls. If not, you probably need a impedence matching box. If so, those are mostly 4 ohm, so you need an amp that can drive 4 ohms.

Used receivers are OK, but you probably want one with HDMI inputs if he is every thinking of Blu-Ray.

Note that zone 2 typically requires analog inputs (receivers in this range can only decode one signal at a time). So, to use his iMAC with zone 2 he is going to have to run an analog cable from the iMAC to the receiver or have a separate DAC. He can use the headphone out jack (assuming is has one) although that means using the DAC in the iMac. Otherwise he needs a separate DAC.

Probably more than you wanted, but hopefully some of it is useful.

I second the Outlaw!

Personally, I've had better results keeping ht and whole house separate. For ht that is simple would be an arcam solo. Whole house find a used denon multi zone for 150 for a 3 zone receiver.

Outlaw audio, or ATI........both great for the money.

Dave

I have exactly the same speakers and use a B&K 507. It's 150W x 7, but honestly, I don't seem to ever have to turn them up very much.

i have a yamaha rx-v1 that i'm selling. it's an integrated amp/preprocessor, 7.1 setup (2 enhanced front speakers), 2 zones, was there top of the line a few years ago. i actually used it with a pair of totem mani 2's which are 85db.

The speakers are only rated at 86 dB so I would anticipate power being a bit more important than with a lot of speakers.

It sounds like you need a receiver that has two or three powered zones and I would recommend getting one that has pre-outs for each channel allowing a dedicated 2 channel amplifier to be added in the future. I have an Integra and have had Onkyo in the past. I think they are very user friendly units.

Something like the Onkyo TX-NR708 would be a great starting point, but is a bit above the stated budget. It has two powered zones and 7.2 channel pre-outs. The 608 is less expensive, but you give up the pre-outs and I would anticipate that the amplifier isn't nearly as good.

There are a lot of good options, but here's a place to start looking. The 707 is the previous version of the 708 and is available on Amazon for much closer to your budget.

Used Marantz MA-500's?