How can I protect ML 436 monoblocks amplifiers?

I did have 2 amps, and I divided them and the rest of my system between the 2 Premiers. The results were excellent, with the exception of the fan noise, which was very loud. I ended up buying 2 computer fans, and placing each one under the Premiers. This provided enough cooling, so that the internal fans didn't go on. I auditioned the P10 when it came out, and felt that it was just as effective as the Premiers. The sound was a little bit richer and fuller in the midrange. One P10 handles my entire system, and is dead quiet. It is really an excellent unit.

Czapp

When you used the 2 Power Plant Premier , you use each one for each amplifier? The results are good?

You change because you need to connect alkl the system in one device?

Islandmandan

I se you have a PS Audio Power Plant Premier in your system.

What the components you have connected to the regenerator?

Last answers , from psaudio:

I Intend to know abolut the possibilities of a power plant premier

"Hi Jose,

In order to regulate the incoming voltage you would need to go with one of the regenerators. Since they are pulling 560W each I would recommend a P10 or two P5s. These would provide protection, regulation of the voltage and filtering of the incoming power.

Thanks,

Marcus"
How aboult the use of one Power plant Premier for the 2 amplifiers?

"Hi,

That would be enough for one and the other components.

Thanks,

Marcus"

In the mean time my local dealer inform me that have a second hand unit of the Power Plant Premier to sell.
So I ask again to Paul if this unit cand handle to the ML 436 monobocks and receive this:

"Jose, this is a regenerator and works great for products. It should be able to handle up to about 1000 watts, so depending on how big your power amp is it should be fine. Highly recommended."

I contacted both MLevinson support, and they inform me to contact the ML distributor to Portugal, the company Genesis Technologies Iberica, but I didn't receive any reply from this company.

From the PS Audio I receive reply from Paul McGowan, and this was our conversation:

At my question, sent, the question of this topic, this the reply:

The P10 Power Plant would be perfect to make certain the voltage reaching the amplifiers is always 230 and to protect and improve their performance.

My reply:

The solution was 1 P10 for Both amplifiers or 1 for each amplifier?

And the other components? Cd PlayStation, record Player, pre- amplifier?

Each amplifier consumation was 560w

Again Paul reply:

You could use just one P10 but you'd be better off with 2. You can use the P10 to power the other units as well.

"Can I espect a protection with the PS AUDIO POWER PLANT PREMIER POWER REGENERATOR ?"

Many manufacturers do not recommend using power regenerators on power amps. This is a question for a ML dealer or contact ML directly.
Also, using a power conditioner/regenerator on a power amp might possibly change the sonic characteristics of the amp.

My advice is to research high quality passive surge protection for the amps. Also, it sounds like you need the power company to check the line voltage coming into your home.

testing

The Power Plant Premier can't handle 2 amplifiers. I used two premiers, then I switched to the P10, which easily handles an entire system, with no fan noise.
Highly recommended.

I am sorry, I don't have any advice but did not want to ignore your request for information. Anyone here has any ideas? Perhaps you can contact PS audio directly.

There is a Multi Voltage Transformer made by Swallow company in Japan.
You need SWALLOW-SU-3000 (3000 Watts) Weight 22kg.
You can put the input at 240V/50Hz and get 230V/50Hz output.
This will protect your Amp very expensive about $850.

A PS Audio P-10 power regenerator would be a very good solution to your problem.

Can I espect a protection with the PS AUDIO POWER PLANT PREMIER POWER REGENERATOR ?

Can he handle with my 2 amplifiers Mark Levinson 436?

Or only considerar this AC REgenerator for the sources, turntable and cd palyer and pre-amplifier?

Thanks

I had similar problems here with unstable voltage. I solved the problem with a Thor PS 10 power regulator conditioner. Below is the URL to the unit. http://thortechnologies.com.au/products/product/ps10-smart-power-station