rauliruegas
Responses from rauliruegas
| Why are my woofers pumping? Dear @o_holter : """ compliance is similar to the Atlas so the test may not tell much........ """"well, you have a " problem " that till today you don't know exactly the reason or reasons for it. You assumed that cartridge/tonearm resonance is ... | |
| Why are my woofers pumping? Dear @o_holter : I think you own a Clavis DC too. Do you already tested with?Characteristics are almost the same as the Atlas regarding resonance frequency calculations. I think you have to test it because you " think " problem is that resoannce f... | |
| Would tonearm with same pivot t9 spindl Dear @radioheadokplayer: The 3P you want has the same P2S distance you are asking for.Btw, how do you know that the 3P is a true/certainty upgrade over your today tonearm?Regards and enjoy the MUSIC NOT DISTORTIONS,R. | |
| Jelco TK-850L review Dear Jelco 750L owners: According with the information in my posts all of you can/could re-align your tonearm to achieve lower distortion alignment levels.Btw, I don't check the other alignment parameters in the other Jelco models but probably sho... | |
| Jelco TK-850L review You only have to be sure that P2S is exactly: 290mm. | |
| Jelco TK-850L review Dear @noromance : There are at least 3 tonearm characteristics than changed in the 850 against the 750: new bearing type ( knife. ), lower vertical bearing sensitivity and lower effective length.All those characteristics are main part of what you ... | |
| SAT 30K+$$ TONEARM: W O R T H T O H A V E I T ? Dear @bimasta: Not exactly as you said. Any one can listen and align any pivoted tonearm taking SAT parameters, independent if the effective length is 9", 10" or 12", por calculations.SAT calculations uses Löfgren A, so instead to use IEC standar... | |
| Replacing Lyra Kleos at end of its life need suggestions as to what next? Dear @radioheadokplayer : Why don't ask directly to the Lyra designer?, you can do it here:https://www.audiogon.com/users/jcarr/feedbacksR. | |
| Replacing Lyra Kleos at end of its life need suggestions as to what next? @radioheadokplayer : Again, not a simple retip.R. | |
| SAT 30K+$$ TONEARM: W O R T H T O H A V E I T ? Dear @invictus005: """ At 80mm null, SAT will not be adequate for my music collection. """Problem is that in general is not adequated to any music collection. Manufacturer numbers does not disclose the reality behind it.""" Why this discussi... | |
| Replacing Lyra Kleos at end of its life need suggestions as to what next? Dear @radioheadokplayer : Exist no one re-tipper that can does the job for your Kleos but Lyra and are very good reasons to that because Lyra as other top manufacturer in reality does not re-tipp but gives you a " new " cartridge/a reborn.The man... | |
| SAT 30K+$$ TONEARM: W O R T H T O H A V E I T ? SAT says: """ higher level of fidelity for 95% of the time over having less angular error on 5% of the tracks. """that's a tricky statement with foundation in a non true premise that the most inner groove is at 75mm when it's not.SAT says that m... | |
| Cartridge Loading- Low output M/C You are rigth about and I did not think you have an issue with my posts.R. | |
| SAT 30K+$$ TONEARM: W O R T H T O H A V E I T ? Dear @advanced101: Well, what SAT did it was a paremeters manipulation choosing stays out of IEC,DIN or JIS standards. SAT says that those standards parameters almost never happen but I measured 20 LPs and I found out no one that even the SAT num... | |
| Cartridge Loading- Low output M/C Dear @catcher10: Yesterday I made in deep tests again along the cantilever stiffnees issue.Wyn posted in this cantilever regards: """ certainly not on tracking which is demonstrably false based on IM tests on tracking performance that I have i... |