imhififan
Responses from imhififan
| Issue with Grace Tonearm https://www.ebay.com/itm/Grace-G-560L-565F-860F-860FB-G-660P-G-960-12-Tonearm-Alignment-Protractor/1... | |
| Can hardware change speaker phasing over time?? I wired the speakers back to "in phase" and the world was right again. I have a wandering phase issue, either with one of the speakers or the electronics in the receiver or amp. I suggest you test your B&W CM10s polarity with a 1.5V batt... | |
| Issue with Grace Tonearm Itn’t the G-520 = 8", G-540 = 9" and G-560 = 12" ? For a normal arm, the second digit of the three-digit number of the model number is a guideline for the length. For example, in terms of length, G-520L <540L <560L. http://20cheaddateba... | |
| Input limited Use the tape loop of your SAE 5000? http://www.swingmusic.net/Audio_Remastering/SAE_5000_back_opt.jpg | |
| Sub wiring help, high level speaker terminal to RCA line level Sub inputs The clarification I am looking for is the “Parts Express” LOC, that is mentioned earlier in this thread. It states that it has a 30 watts max rating. If my amplifier is rated at 400 watts, what reliability concern is there due to the vast differen... | |
| Input limited You can use the Tape1 and Tape2 "PLAY" as a line level input. For example, connect the CD player output to Tape1 "PLAY" input, switch on the Tape Monitor1 for CD playback, switch it off to select other source. | |
| Issue with Grace Tonearm I believe your Grace 560 is a 12" tonearm and the mounting distance is 270mm, make sure your turntable plinth is big enough to mount this arm. I suggest you post your question in Analog section, you will get more response. | |
| Thiel CS1.6 How to remove woofer? Lay the speaker down on its side, unscrew and open the bottom plate, then unscrew the four mounting bolts on woofer and you can move the woofer out from the bottom. | |
| T6.3AL250v Fuse: Slow or Fast Blow??????? Yes, it is a slow blow, low breaking capacity fuse. | |
| Cons of using main XLR/Balanced outs for subwoofer? Is there any harm in using the main XLR output to send signal to the subwoofers, and using the 1, or 2 RCA output to send signal to the main drivers? Go for it, McIntosh C220 has separate buffer on each output. | |
| Separate subwoofer amplifier with remote. What would work for stereo setup? Check out the OSD Audio’s SMP500DSP or Velodyne SC-600D, both come with remote control. I use a Velodyne SMS-1 connect to Sunfire stereo amp to power a pair of 15" passive sub. | |
| Rebuilding Power Amplifier(s) Now I have no experience of such work , but I can't see any great skill needed for such work. All I can say is GOOD LUCK!!! https://liquidaudio.com.au/hall-of-shame/ | |
| Speaker terminal polarity In storage for over 15 years, power it up in series with a 100watts incandescent light bulb just in case... https://encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcQNxTsL4-umotgX_8DKUzPmho7DSPJzqsQ_fg&usqp=... | |
| 845/211 tube amplifiers with kef reference 5? Bel Canto SET80 use 845R power triodes and output 70Watts per channel. https://www.stereophile.com/tubepoweramps/598bel/index.html | |
| Mystery Capacitor and the Tangent RS4 Crossover The cap was somewhat damaged as I removed it from the circuit board so I was just a bit concerned about whether it would measure accurately. That "infamous pink mystery cap" also known as "Tropical Fish Capacitor". Some DIYer still using it for... |