imhififan
Responses from imhififan
| Krell KRC3 preamp @ei001hYou need to remove the top cover of the Krc3, look for a red dip switches labeled "Input configure" and set the S3 to Proc. position. | |
| Krell KRC3 preamp My suggestion:the "stereo audio out" on the oppo 205 connect to KRC3the "5.1CH audio out on the oppo 205 connect to MX135use a Goldpoint SW4 Main out connect to KAV500 FR and FL inputhttp://www.goldpt.com/sw4.htmlKRC3 output to Goldpoint SW4 Li... | |
| sub to my Mcintosh c40... After a quick look at the McIntosh C40 Owner's Manual,I believe you can connect the kilpsch rsw 10 Line input to either switched output 1or 2 of the C40 and switch on the speaker 1 or 2 accordingly, | |
| Two amps to one speaker Here’s a very recent thread with some suggestions https://forum.audiogon.com/discussions/a-rookie-question-re-two- amps-one-pair-of-speakers The above link was only good for switching between two solid-state amplifier, to switch between a tube a... | |
| Suggestions for active crossover setup please. An inexpensive example: Rolls SX45 Stereo Two-Way Mini Crossover w/Sub Output | |
| Mid Range Remote Volume Control An Infrared Remote Control wouldn't work!What you need is a RF Remote Control to provide +Voltage or -Voltage to a Motorized Volume Pot. https://www.amazon.com/Channel-Wireless-Control-Receiver-Momentary/dp/B00FFW1DI6http://www.ebay.com/itm/10pc... | |
| Why such low power with DIY tubeamp kits? Check out Aliexpress, there are tons of inexpensive tube amp kits.For better quality kits, transcendentsound and dynakitparts are worth a visit too. | |
| A rookie question re two amps, one pair of speakers Or you can go the cheap way and use this one back to front.http://www.ebay.com/itm/A-B-A-B-Switch-1-IN-2-OUT-2-Way-Stereo-Receiver-Speaker-Set-Selector-/152373329362?hash=item237a287dd2:g:Q9gAAOSwNSxVbL5- I think it is not a good choice because... | |
| A rookie question re two amps, one pair of speakers Yes but, it needs to be said a speaker selection switch need to be used back to front.Amps to the speaker connections terminals and speaker to the amp terminals. The link of Niles SPK-1 has a connection diagram and instruction : Common applicati... | |
| Can anyone identify these speakers? A homemade dahlquests DG-30? | |
| A rookie question re two amps, one pair of speakers George is right, do not connect two amp output to one pair of speakers! this topic had been discussed many times, best way to do it is using a speaker selector switch.I had use a Niles SPK-1 years ago, it switch the connection automatically from t... | |
| Measuring room acoustics Check these out: RTA Audio Analyzer Measuring your Rooms Acoustics with the Impulso App PMIK-1 microphone | |
| NO Side Speakers in an atmos system? ozzy,Btw, to my ears Dolby Astmos dose not made a day and night difference. | |
| NO Side Speakers in an atmos system? I play a Atmos Blu Ray through my Oppo 105 outputting via the 7.1 channel RCA analog output of the Oppo into a Denon Receiver (again via the RCA inputs) Dolby Astmos must use HDMI connection and set output to bitstream out to receiver/prepro,... | |
| Driving me crazy To eliminate its not the room caused the problem, can you connect a headphone to your power amp speaker output by using a headphone adapter to confirm it? |