dover
Responses from dover
| Fidelity Research FR64s Headshell dilemma @nandric I'm sure you can figure it out, but if you cant, the doctor mistakenly thought she said "I have a cute vagina". | |
| Fidelity Research FR64s Headshell dilemma Anytime i have new tonearm and cartridge i follow manufacturer recommendation only, i trust to tonearm/cartridge designer more than to anybody else! The experts once thought the world was flat, too, until someone ventured west, and was stunned to ... | |
| My AT150MLX Cartridge has been misaligned for 4 years You have probably damaged your records. If a cartridge mistracks - the groove is permanently damaged.You might want to change your moniker. | |
| How to adjust height of Eminent Technology ET-2 tonearm I've set up the ET2 on various Sofa turntables dozens of times when I was the importer here in New Zealand ( for both products ).I've always been able to set up with the ET2 mounted directly on the Sota armboard without any spacer required other t... | |
| Fidelity Research FR64s Headshell dilemma In fact for your Denon DL-103 with its conical tip the alignment method is absolutely irrelevant! Why? Because the stylus is CONICAL. Before you will twist your cartridge in the headshell to align it with something else like Baerwald please try to... | |
| Thoughts on SS bass. Tube mid and high tube pre The Tannoy Monitor Gold's crossover is in the midrange - 1000hz.The tweeter and base are aligned with the crossover and physical position such that at the cross over point the tweeter and base are perfectly in sync with both phase and time - hence... | |
| 2020 update : JC Verdier La Platine But when I got Graham motor I tried rubber, original thread and some special fishing string as a belt again before I changed it to Delrin pulley and mylar tape. Difference was huge and striking. The highs were so dirty and compressed! I could not ... | |
| Tonearm mount to the plinth vs arm board vs rotating arm board vs isolated tower 05-12-2020 1:23pmIn the case of the first you have a subjective means to winnowing out how a separate arm pod is a failed concept;THE ATMASPHERE PRINCIPLETHE 'FAILED' CONCEPTThank you for reminding me of why I dont use rubber belt drive turntables... | |
| Tonearm mount to the plinth vs arm board vs rotating arm board vs isolated tower My turntable however, sits on a HERZAN ACTIVE ISOLATION STAND which cancels all vibrations from 0.5Hz-100Hz.Very good - but I prefer my music full range, if I didn’t want to hear anything below 100hz I would listen to Tin Cans.Your herzan cant mov... | |
| Tonearm mount to the plinth vs arm board vs rotating arm board vs isolated tower The base weighs 18 lbs (8.1 Kg)......But a SOLID GRANITE CRADLE, whilst not as heavy as cast metal.....was GOOD ENOUGH and relatively affordableReally - mines 68kg, and utilises SPZ which dissipates any energy between 4 and 100hz internally at a m... | |
| Ikeda 9 Cartridge Squeaking @neonknight Can we get a concensous of which version this is?The one in this image is the cartridge I have. Are we talking an original series 9 or the Kawami? https://conchan1.files.wordpress.com/2016/06/mi-last.jpegThe cartridge in the photo is t... | |
| Garrott vs Soundsmith @nandric Everything has been covered here. Andreoli is an artisan, who I suspect gets bored with producing the same product over and over - once they have mastered or achieved their goals on a particular design, they then look for a new challenge.... | |
| Ikeda 9 Cartridge Squeaking @neonknight I own an Ikeda Kiwami, purchased new in the 90's.The correct tracking force for the Kiwami as per the manual ( which I have ) is 2.0 - 2.5gCompliance is 6 x 10*-6 cm/dyne.I have succesfully run it in a Naim Aro with effective mass 14g... | |
| Tonearm mount to the plinth vs arm board vs rotating arm board vs isolated tower That’s the advice you get from ’amateurs’....🤪HERE is the ’reality’ from Mark Doehmann, responsible for the designs of the Continuum Caliburn and Criterion turntables as well as his own Doehmann Helix 1 and Helix 2 turntables.....all of which are ... | |
| FR66S vs Ikeda IT-407 vs FR66FX FR64S is best bang for the buck. FR66 is better, but expensive to buy.66FX I have never heard, but is lighter mass and costs less to buy than 66S. 407 has mixed reviews - most folk believe the FR64S/66 are the best built, and sounding. There have ... |