atmasphere
Responses from atmasphere
| Tubes vs Solid State Matching amps and speakers is important!Take a look at this link:http://www.atma-sphere.com/Resources/Paradigms_in_Amplifier_Design.phpThe B&W 802 is designed to work on an amplifier that can double its power when the load is cut in half. Spec... | |
| Oil For Nottingham Spacedeck? Generally with any turntable platter bearing(s) you can use a few drops of Dextron automatic transmission fluid with no worries! | |
| Empire 498 We can service a lot of that stuff- we even got the correct motor mounts re-manufactured. | |
| Lazarus cascade classic and Mark III amp's The Lazurus was based on the 'Last PAS' construction article published in what was back then called Audio Amateur in the late 1970s or early 1980s.The Mark 3 (I assume Dynaco) you can find by Googling images of the schematic. | |
| Could use your advice re: tube gear If your amps were in storage, its likely they are not working up to snuff. The Marantz was a nice amp but unless its been rebuilt/serviced recently I would not expect it to sound right- in fact I would be nervous about plugging it into the wall!A ... | |
| what is an ideal tube amp Charles1dad, take a look at this article, it will help in understanding my explanation that follows:http://www.atma-sphere.com/Resources/Paradigms_in_Amplifier_Design.phpFour ohms came in with the transistor- we all know that. However, along with ... | |
| Good amp match for vinatge Vandersteen 2C's? The first time I heard the 2C was with a very early set of our amps. They were revealing and musical- no troubles making bass either. We did several shows with Vandersteen speakers, using our smaller amps. One time Richard came into our room to ch... | |
| what is an ideal tube amp If a tube amp with an output transformer has a 16 ohm tap, it will have slightly more power and certainly less distortion when driving 16 ohms. This is because the output transformer is more efficient. In fact it will also exhibit more bandwidth- ... | |
| what is an ideal tube amp John also has an Atma-Sphere setup, with a fairly well-optioned MP-1. He has had Atma-Sphere amps since 1989 if memory serves.I bought a set of T-3s in 1998. There has been no looking back. They have been updated with the dual woofers, new crossov... | |
| Plinth mass vs. Foundation mass The coupling between the platter and the tonearm must be exact. If the platter is moving with respect to the arm, the cartridge will interpret that as a signal and a coloration is thus introduced.Thus the plinth should be utterly rigid and devoid ... | |
| Headshell Washers : Nylon or Stainless Steel? Moonglum, titanium washers get used by high end bicycles all the time.http://www.nylonalloys.co.uk/cgi-bin/shop/nylon-alloys-categories.pl?TITANIUM|METRIC| | |
| Ground Cheater plug or.... Al is correct. This will not be solved by cheating the ground. Grimace, you've not mentioned your speakers; if they have an efficiency of over 100db or if your room is really really quiet this might be perfectly normal. | |
| Headshell Washers : Nylon or Stainless Steel? Moonglum, there is no need to worry about ground looping the cartridge when mounting it in a tonearm.If mass is an issue, go with titanium washers.I would avoid nylon as the cartridge has to be coupled to the tonearm as rigidly as possible otherwi... | |
| what is the best sounding speakers for under 5000. http://www.audiokinesis.com | |
| Tube biasing question please The higher initial reading of the set you just installed indicates that they have more transconductance, which is a good thing. It can be an indication of hours but that can't be counted on due to the variance in the tubes themselves. |