Upgrade from Pass Labs XA30.8 to X250.8. Worth it?


I am getting ready to make some upgrades to the system. I currently running a DAC into a BAT51SE, then a Pass Labs XA30.8, then finally into Decware DM947 speakers (don't worry if you've never heard of them; not the last word in speakers, but have been doing a solid job for about 5 years now.)

I am contemplating moving up the Pass Labs amplifier line, and the X250.8 looks attractive. I would like to hear more bass authority and definition, but I don't really want to sacrifice the mids and highs of the 30.8. 

I would love to hear some of your impressions of the X250.8, especially if you are able to make some direct comparisons to the XA30.8. I've spoken with both Mark at Reno Hifi, and Kent English of Pass Labs; both are wonderful and informative people. What I am interested in now is the opinions and experiences of end users of either of these amps. 

Thanks! 
willrich47
Your calculation of the 18K is correct, and I feel pretty certain that your diagnosis of the bass issue is correct. The 18K load impedance divided by the 4.7K output impedance at 20 Hz is a ratio of 3.8, well under the rule of thumb guideline of a minimum of 10. And the wide variation from 410 ohms to 4.7K makes that situation particularly bad. (If the output impedance were 4.7K throughout the audio band the consequences would be mainly a slight gain reduction and increased sensitivity to cable effects, and perhaps a small degradation in the distortion performance of the preamp. While the large difference between the output impedance in the bass region and at higher frequencies, in conjunction with the heavy load impedance, will cause both frequency response issues and frequency-dependent phase shifts in the bass region).

To add to bdp24’s suggestions, a few years ago another member here, who uses Audio Research Reference series electronics, very successfully resolved a similar issue by having a tube-based buffer stage, providing suitably high input impedance and low output impedance, custom made for him by Tom Tutay of Transition Audio Design in Florida. It would be inserted between the preamp and the sub. I believe the cost was considerably less than $1K, although in his case balanced interfaces weren’t necessary. I don’t think Tom has a website, but a Google search should provide you with his contact information.


Good luck. Regards,

-- Al


A slightly old thread but thought I'd comment.  I have an XA30.8 (which itself was an update from an XA30.5) and had upgraded my speakers to Tekton Double Impact in my living room/primary setup.  The tonality was great, but I wanted to get more of that super-sharp imaging feeling/a bit more accurate reproduction, so after a few questions to Mark at Reno HiFi he strongly suggested trying the X250.8.

I did and have been quite happy with the results.  Mark may have found the perfect setup for me in the X250.8 + Tekton DI.  I haven't really noticed any degradation in tonality (but I never get anywhere close to the end of the class A envelope of the X250.8 even in my large living room at reasonable listening levels), but I *have* noticed the increase in imaging clarity, bass reproduction, and sense of crisp/dynamic control across the whole range.

I still have the XA30.8 in my secondary setup with some Amphion Argon 2's and the sense of lush tonality is great when I'm in the mood for it.

So I think it depends on what you're after.  The XA30.8 is already a bit of a move away from the "lush class A" sound in the XA30.5 I'd had before, but I enjoy accuracy of reproduction.  The X250.8 seems to be where they tried to give it yet more control and sharper reproduction while keeping at least some of the XA.8 magic.  Maybe that describes the differences between the X and XA series in previous generations as well, but at the .8 series it seems to have found a point where I'm pretty happy with the X and XA lines, with the X250.8 being my personal favorite so far.
In this price range Luxman m700u could have the edge in term of power and industrial design and I hope someone can compare them. I know WC compare the brands but different models.
@ebolyn

Even though this thread is a little old, your observations are still incredibly relevant. When I first started this thread, the question came down to new speakers, or a new amp. I made the decision to get new speakers, which was the right decision at the time. The Double Impacts have had a remarkable impact on my system. 

But it here I am again, looking at the upgrade to the X250.8! In a way, your timing couldn’t be better! 
Post removed