2. amps-preamps
  3. 1079970521

Possible move to tubes… help direct me

A recent speaker change has left me with too much amp. I’m very happy with my Pass x250 amp. The speaker change provides me with a good reason to see if I can downsize my amp and maintain or improve the quality of sound. I would like to consider tubes. I have tried to do my homework by reading through the pertinent discussion boards here (I just e-mailed Roy at GMA for advice) as well as talking to a few members on Agon whom I have built a relationship with. I know this is a dangerous post because of the infinite possibilities, but I'm hoping to find consensus on a few models.

My situation:
1. I don’t want to go backwards from my Pass in terms of sound quality
2. One of my options is to do nothing and keep the Pass
3. Budget $3k or less new or used
4. I need at least 70 watts in 8 ohms tube amplification
5. A good first step in tubes (no experience with biasing or tube rolling)
6. Power amp or integrated is fine
7. Nice accurate bottom end with smooth mids and highs
8. I’d like to stay semi-mainstream on manufacturers because north east Ohio is not a hotbed for 2 channel audio and I’ll have to travel to find dealers.
9. Room is a rectangular living room 14x22x8
10. Music is Keb ‘Mo to Alison Krauss

Thanks.
mijknarf
meisterkleef
146 posts
 
You can *NEVER* have too much amp. Keep the Pass. It's an
awesome piece.
jfrech's avatar
jfrech
1,816 posts
 
The bat VK60, SE or vk 75 are all super choices. The 75 goes from 60w to 75 per channel. I'd expect much better midrange warmth, depth, air, images. Your pass might be better on the tightness on the bottom end. Usual things for ss vs tubes.

The BAT tube amps are autobiasing. So it's plug a new tube in and play away.

While you can't roll the output tubes, you can roll the input 6sn7's. Makes a big difference. You can really change the sound of the amp depending on the front 2 6sn7's.
kkursula
95 posts
 
Stehno, that is an unusual suggestion?! Btw, I myself would be hesitant to dump Pass amp for anything less than any Lamm amp.
sbank's avatar
sbank
3,378 posts
 
Mij,
A concern & a suggestion...

I'm not sure if the EVS has XLR outputs. If not, then to use the BAT amps, you'll need to use their XLR-to-RCA adapters. This functions okay, but loses some of the benefit of the BAT all balanced design. Many(perhaps most?) comments about how good BAT gear sounds, is based on it being used in balanced mode. Granted, you could probably get a vk60 & vk3i for $3k; a vk60 & vk5i for $4k. OF course, you could try w/the EVS & adapters, and upgrade to a balanced config if necessary. I agree w/the others that this is great sounding stuff, and simple & elegant.

Although not too widely distributed, a long-standing company that would give you a nice option is Air Tight. Their ATM1 or ATM2, both have two inputs and volume controls, so you don't need a preamp. Technically, I believe it's a passive line stage though, so they don't refer to it as an integrated. Easy to bias, w/readily available tubes. Even though rated at only 35w, the ATM1 has driven many difficult loads(relatively speaking) with grace. It's very musical, and holds it's value well. The ATM2 has more power at a higher price...
Good luck,
Spencer

mijknarf OP
266 posts
 
I like the advice on all suggestions, especially the BAT amps. Unfortunately, my Jolida is only rca out, and my attenuators are naturally rca as well. I'd love to operate the x250 in balanced mode, but it's not in the cards right now. Ideally, I'd like to upgrade the source to one with volume control and balance outs so it would go into my existing amp or one of the BAT amps recommended. No doubt I could get by with some adapters, but that's not the way to operate. From what I've read about the vk60 and vk75, the vk75 is probabaly what I'd want to move to (if I did change). Decisions, decisions.
More to discover