Replace the cheap tube Sockets with Teflon units and you will get the best improvement. |
Have you tried calling Audio Research direct or an ARC dealer? |
For those who have bottom getters like the RCA smoked glass VT-231 and Sylvania 6SN7GT and are using Herbies tube dampers, you might try moving the damper all the way down the glass to where the damper just touches the base. I recently found that a second Herbies damper attached directly to the tube base was quite efficacious. |
I found this article in Stereophile about Audio Research tube dampers? I've tried to locate a seller online, but haven't had any luck. The AR website isn't very helpful.
Anyone know where to find these or have any experience with them?
http://www.stereophile.com/content/audio-research-reference-phono-preamplifier-audio-research-tube-damping-rings |
Herbies top of the line better bass quieter etc. |
Audiolabyrinth, I use herbie's dampers on a Jolida cd with 12AX7s. Result was more focused image, tighter bass. But again, the placement of the damper is important; for me it is near the top of the tube, level with the top of the plates. |
very interesting thread I must say!,learned alot,wanted to say Hi to gammajo,my question is,has any one tried these tweaks on a tubed cd-player like ayon to good effect or bad?,the cd 2s or 5s players. |
" If you hold your speaker cable while the music is playing, do you feel any vibration?"
No, I dont feel any vibration in the cable, but I wonder if Steve (Herbie) is right about vibration on the connectors, especially a RCA on a IC?
Every Herbie's tweek I have used has resulted in a noticeably improved performance. The tube dampers being the most jaw-dropping improvement. |
Lowrider, yes I have the Herbies dampers for components with the larger, softer contact material. I find using about 4 or 5 per speaker cable cleans up the sound, not to the degree of the tube dampers, but audibly nonetheless. I've only heard them applied to speaker cables in my system, and I expect their impact will vary depending on the system at hand. If you hold your speaker cable while the music is playing, do you feel any vibration? |
Kernelbob, Herbie's makes dampers for IC connectors, but please explain to me how and why you damp speaker cables. I'm still not sold on the effectiveness of the IC dampers, but what are your findings with your speaker cables?
thanks... and I'm a faithful Herbie customer. |
My experience is that tube dampers are essential. They can improve low level resolution, microdynamics, and allow higher volumes before distortion limits the volume at which you're comfortable. One thing I've found is that it's important to damp the tubes, but not to add mass that can store vibrational energy and then release it. Specifically, I recommend avoiding those tube damping rings that ARC supplies with their preamp tubes. Substituting Herbies Ultrasonic tube dampers on my ARC REF3 preamp eliminated a smearing quality compared with the ARC o-ring dampers. I mentioned this to ARC when I ordered tube replacements.
I do use very thin o-rings on the brass bases of my Kronzilla T1610 tubes. I find that four of these (1/16" thick and 3-1/2" diameter) made a surprising improvement in the sound, with instruments sounding more like solid and independent sources. Interestingly, when I tried putting those thin o-rings (rated to 450F) on the glass of the tubes, they start to smear the sound. For the glass envelopes, I use three Herbies tube dampers per tube.
There's lots of different types of dampers out there. I'd appreciate the input of those who have compared the Herbies dampers with other designs. One more thing, I've found that damping speaker cables also provides improvements. |
My experience in my Jadis tubed preamps (using Tubesox, Top Hats, Vintage Tube Service's brass dampers (the best of the ones I tried) and Mapleshade dampers) has been that the better tube dampers take away a little bit of that tube warmth but give a bit more focus and clarity to the sound. This would be consistent with lowering the tube microphonics, getting rid of a small amount of distortion. Given the commparatively inexpensive choices available to you with the Herbies and Audio Research dampers, you might just want to experiment and see if you like the sound better with or without. |
All tubes are at least a little microphonic; if you don't believe it, try a Herbies tube damper on a supposedly non-microphonic tube like a Military grade 6SN7 or 12AX7. |
I am using a Joule Electra OBS-1 which has 6 tubes in the preamp part and more in the power supply but I wouldn't think that they would affect sound (I could be wrong). I think of old Fender Teles with microphonic bridge pickups- the microphonics add a nice part of the tone but once it gets loud they screech and are a problem. Maybe damping a tube (even if it is not noticably microphonic) could take something away from the sound. And yes,I know, tubes are not electric guitar pickups. |
I did not like the effect with my Audio Horizons Preamp (lost openness and aliveness) though it did stop microphonics |
Yep, I added some Audio Research rubber band-like tube dampers to my Manley Steelhead phono preamp and I heard a tightening of the sound, especially in the bass, and improvement in dynamics. It didn't make the difference other tweaks such as Audio Prism cables or Kemp Elektroniks plugs made, but still a very cost-effective tweak. |
"I have heard one person say that they heard a reduction in openness and soundstage when using a damper. Any opinions of this?"
Results may vary on each system; I haven't heard, that but I know from experience that postion of the damper on the glass tube will produce a different effect. Herbie recommends placement 1/3 down the tube. Why not google Herbie's audio lab... there is a Q & A section. |
Hi Rmcfee
I would say it would depend on a lot of things. What was the piece of equipment the dampers were used in? What kind of damper was employed? There are many kinds now. From silicone rings to brass rings with a ground wire.
I've used silicone rings and Herbie's tube dampers on the preamp tubes of my amp and I had the same results as Lowrider. |
I have heard one person say that they heard a reduction in openness and soundstage when using a damper. Any opinions of this? |
I also use Herbie's Tube Dampers in my preamp (4 tubes) and the result was a tighter bass. |
Thanks MOFI. Can you describe the improvement at all? |
I use Herbie's Tube Dampers on all of my tube gear. I wouldn't say it's a profound difference, but well worth the asking price. It's a pretty cheap tweek that works well...IMHO. |