Technics SL 1200 GR

I think you'll be pleased with that AT cartridge.

Here's a common sort of stylus gauge...

Stylus gauge Amazon

On my SL1200 I use a tracking force of 1.8g for my 540ML.

Technics advises to set the antiskate to the same value as you set the tracking force. That's done using a small dial near the back end of the tonearm. 

The GR is the best sounding table I’ve encountered anywhere near the <$3K price point. 

You really must step up to a $5K^ belt-drive table or the 1200G to get a worthwhile improvement. Even with a $5K belt drive you might have to sacrifice some pitch stability when it comes to sustained notes.
 

Guys, the table arrived yesterday and its simply stunning. Love how it looks and feels. The heft and weight feels solid compared to the Rega (which felt quite light to be honest). I'm not saying it in a negative way, coz I know Rega is all about its engineering but the weight of the 1210 gr does feel nice.

@newfzx7 thank you.  the AT cartridge will arrive today. I bought one that's already installed to a head shell. Its supposed to be pre-aligned.  My stylus gauge and protractor doesn't arrive until tomorrow. Should I wait to make sure i have the accurate tracking force and alignment or trust the cartridge alignment and Technics tracking force knob?

@helomech thank you. I am extremely pleased with the table and i don't doubt it one bit. Can't get better than this for the $$. 

The Technics SL1200GR is a great turntable for the money, especially for a low fuss user who isn't inclined to go down the rabbit hole (plenty of time for that later). I am currently using that table with assorted carts and have no reason to upgrade until I am ready to spend significantly more money ($5k plus for table, $5k plus for phono-preamp, and $2k plus for cart – plus hours of time).

My favorite carts for the SL1200GR are a Hana SL (.5mv output) running into 1kohms (the cart needs >400 ohms minimum, but opening it up can sound better in some systems, some people run them wide open but I find that a bit harsh).  I also really like my Mofi MasterTracker MM (3mv output), which of course I run wide open (47kohms) and can be run using a standard MM phono pre input. (that Mofi MasterTracker is similar to the AT cart you are looking at but has better build quality).

The Hana ML has lower output and will require a better phono preamp to a step-up transformer to extract its value.  You have to decide how much you want to spend on a phono pre.  I'm satisfied with a $1.7k Odyssey Suspiro for my modest carts; you will need to spend considerably more if you are looking at high end ($2k plus) carts.  The HanaML is a great value cart if matched with the right phono-pre, without the right pre you will likely not notice a difference between the ML and the SL.

Everybody talks up the Denon 103, but it is too heavy for the medium compliance arm on the SL1200 GR.  If you want to go that route, do your research on tone arm compliance.  I can get my Shure V15 III to work, but it really needs a high compliance, lightweight arm to work well.  The arm on the SL1200GR works with a wide variety of modern carts, including ATs, Ortofons and Grados.  The removable shell makes it easy to swap carts!

@kahlenz Thanks for taking the time to validate my decision to purchase the 1210 GR. It really means a lot to me. also, the recommendations on Carts.. I am still trying to understand what’s required to run LO vs HO MC carts vs MM carts.

My Marantz PM KI Ruby states the following for input sensitivity/Input impedance:

• PHONO (MC): 250 μV / 100 Ω/ohms
• PHONO (MM): 2.3 mV/39 kΩ/kohms

Is this what I should be referring to when deciding whether or not my marantz is good enough to drive for example, the Hana SL? You’ve mentioned minimum of >400 ohms..looks like my amp is nowhere near that mark.. lol and its not even good enough to run the Mofi MM that requires 47 ohms?