Clearaudio Concept and Audio Technica AT6006R tonearm lifter???
My first Safety Raiser cost me $19.95 and treated my Unitrac arm very gently, for 30 years. Ten years ago it got a bit too energetic, so: found a NOS/NIB replacement and paid $129.00 (gladly). The box still had the $19.95 tag on it. A little trick that makes adjusting the Raiser a snap: Stretch the thinnest O-ring you can locate over the inner tube, to hold your height adjustment, while you determine/lock the horizontal position. |
@Kingharold I see how the space is more limited with the Tracer (what a beauty btw). My recommendation is to get the AT-6006R and try it on the tiny space between the black round base and the silver base. Something I did not try because it was not necessary but was in my options plan, was to bend the lift wire trigger to a position where it will be reached by the tonearm out of the way of the platter, it seems to me like that could work. All other options are either not elegant or have a larger footprint or are too expensive to just try it out. Clearaudio Performance DC with Tracer Tonearm |
Very neat installation. It looks like it came from the factory that way. I have the Clearaudio Performance DC Wood with the Tracer tonearm. The arrangement where the tone arm post meets the plinth is quite different from your Concept. I haven't seen a lift I think would fit. If anyone has a suggestion I would appreciate hearing it. I have an old Q-Up I used on an AR turntable about forty years ago that I might be able to use with a spacer, but it looks so cheesy I don't want to mar the looks of my turntable with it. |
The Q-Up will definitely not fit. @markj941 , this is a very common problem. Your best approach is to raise the lift as high as possible so that with the lift cocked it just barely clears the tonearm. This raises the trigger as high as possible making it easy to slide the record in under it. You will notice that records with a tight spindle hole can be tough to get off the table. I suggest a spindle hole drill. In my experience, the best lifter out there is the Little Fwend. It is much better made than the others and the lift post cross section is square so the lift does not rotate around. They also make a special base for Technics turntables that fits in tight spaces and allows more adjustment. I use it on my Sota. The Tru Lift has a trigger that will not overlie the platter but otherwise is not a good design without modification. The post cross section is round so it can rotate. The lift platform is metal. The tonearm will slide easily on it. What happens is the lift picks up the arm and the antiskating force causes it to slide backwards off the lift. If the turntable is still running the stylus lands back in the groove and the arm then gets trapped against the elevated lift. Yuk! My own fix for this problem would be to mark where the tonearm contacts the lift and grind a notch at that point the tonearm can land in. Another approach would be to tack a thin strip of 100 grit silicone carbide sandpaper to the underside of the arm with double sided tape creating a high friction contact point. |
There can be a need for a bespoke fit base to be produced, where the base enables a Tonearm Lifter to be positioned in a manner where it does not encroach the space required for other functions or allow for an adequately secured placement. It is best to stick with a Lifter, as there is additional piece of mind to be had knowing it will remove the Styli from the Groove.
|
@markj941 I read your post when I first ordered my Clearaudio Concept Wood for my second setup since I really like the AT6006R Tonearm Safety Lifter on my VPI Prime Signature TT. Once I got the Clearaudio I took measurements of my lifter to calculate if I could place it between the tonearm shaft and the tonearm lift bridge... I was not 100% sure but I ordered the additional AT6006R anyway... Well, I got it today, and although it took a couple more measuring steps than my first one, it works perfectly well... Not only that but it barely changes the simple aesthetics of the Concept... is almost hidden. Let me know if you want more pictures or advice on how to install, Maybe the basic guidance is that you don't need any of the extension pieces (you can build a stylus cleaner with those extra pieces and blue putty on top) and, the trigger/antenna goes a 1/16 inch under the lift bridge. |
I purchased my AT from Knight Sound & Lighting for $116.10 delivered. I looked at the Q-up and the built quality and performance is really not even close to the AT. Like I said in the original post, The new 6006R AT functions as smoothly as any of the high dollar offering, but at $116.10 delivered it's very hard to equal. |
I use the Q UP, and although ‘fiddly’, it works, and only costs less than a 1/4 of the AT. Of course it’s hard to believe the Q UP costs as much as it does considering it’s build. I always look at the AT lifter as a replacement, just for looks and build quality alone, but the OP makes an interesting point about a possible lack of location not to interfere. I can see where that could be an issue. The Q UP is already fairly tight in its placement on my table, and is much ‘thinner’. |
My JVC Spinner, TT81 (many others) is 1-1/2" above the plinth, so the lifter needs to be raised up via it’s extra height blocks, each level in the stack separate self stick adhesive. Also tonearm post needs to be long enough, I had to add a 3/8" spacer below my arm, OEM made it for me. Good luck with the Q UP, I tried it, couldn’t get it proper height. And it’s flexible plastic sides spread too easily, bar would not stay in the notch where I put it, I sent it back, The Audio Technica, except for price https://www.amazon.com/gp/product/B07HKX6WL7/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1 is very nice, much more substantial. Because I have a long 12.5" arm, and it’s small base, it was easy to locate, stable stacked base, works great and not extended over the LP. There is no space for a riser between my 9" arm’s base and JVC TT edge which extends beyond the platter diameter. |
The Q UP might be worth a try!! http://www.thequp.com/#:~:text=The%20Q%20UP%20is%20a%20high%20precision%20device,is%20designed%20to%20fit%20on%20most%20manual% |
