jea48
Responses from jea48
| Anyone have this turntable issue? Thanks Al (almarg).Here is what the SP3 manual says about the volume control. Page 5 D: VOLUME CONTROL / ROTARY ENCODER Continuous rotary optical encoder for determining volume level as well as an input for most variable settings and other sel... | |
| Anyone have this turntable issue? @almarg Did you look through the owner manual of the SME V arm? Check out "515 Audio Lead" found on page 12. https://sme.co.uk/audio/wp-content/uploads/sites/1/2016/12/SME-series-v-instructions.pdf I assume the OP connected the single ground from ... | |
| Anyone have this turntable issue? I agree with elizabeth, it has to be static.With the volume control turned all the way down it must be a hell of a static charge.What is the the percentage of humidly in the room?Belt drive TT? What material is the platter made of?What are you usi... | |
| High quality in-wall UL-C2 rated 10-gauge A/C wiring ? I am looking to re-wire my listening area front-wall with a dedicated A/C circuit using 10-gauge UL-C2 rated in-wall wiring. I know Audience makes a high-quality one however I didn’t want to pay $26/foot. https://www.tweekgeek.com/audience-in-wal... | |
| power grid issues? greg22lz OP 180 posts 05-31-2019 11:22amthe hum i am referring to is my transformer on my tube amp. PG&E has assigned an EMF specialist to help determine where the noise is generated. I do not believe at this time that it is generated from m... | |
| New dedicated lines have high noise floor. @ pg62 AC Power Wiring Types (cont’d) Metal Clad (MC)is manufactured in both steel and aluminum with twisted conductors that help reduce AC magnetic fields. Although the steel jacket helps reduce AC magnetic fields, the twisting of conductors has... | |
| New dedicated lines have high noise floor. @ pg62 Why did you use hospital grade MC cable?For audio 10-2 with ground would have been better. Problem with hospital grade MC cable there are 4 wires. one Hot, one neutral, and two equipment grounding conductors. The geometry of the way the 2 e... | |
| Need help regarding isolator wiring configuration. @ vze2r8xz Because of the 6-20P power inlet my guess is the primary input voltage is 220V or 240V.Secondary output voltage is 115V or 120V.Connecting the primary to 120V will only give you around 60V on the output.Make sure you check the output vo... | |
| Need help regarding isolator wiring configuration. https://imgur.com/a/pFAgCYtIt has a single primary winding and a single secondary winding. (It is not a balanced power output system)It appears to be wired as an "Isolated Power System". In English the secondary output of the transformer is floati... | |
| Need help regarding isolator wiring configuration. Assuming the OP is correct, the transformer primary winding is fed by 240V. We don’t know if the primary is designed as a dual voltage 120/240V. (Two windings) The unit’s input is a 6-20r input plug which needs to be replaced with a 20 amp iec inl... | |
| Need help regarding isolator wiring configuration. I couldn’t get any of your links to work.As for the 6-20R. The number 6 signifies 250 volt. Next number is ampere rating, 20 amps. R = Receptacle.I think you might mean 6-20P, inlet plug.Example: https://www.westwayelectricsupply.com/wiring-dev... | |
| Ground Loop(?) leads to blow speaker @atmasphere You must have missed the OP’s last post. solobone22 OP11 posts 04-28-2019 2:47pm Update: I went to test the Creek and it wouldn’t power on. Opening it up I found the 2 fuses on the board were blown. Unfortunately they didn’t blow b... | |
| Who Makes A Good Duplex Wall Outlet elizabeth 7,012 posts 04-25-2019 8:51amFor $$$ ’high end’ duplex. one should actually go for duplex designed and built TO BE high end duplex. Not all those ordinary types ’gussied up’ with fancy treatments. I went with Furutech. Designed from th... | |
| Ground Loop(?) leads to blow speaker Al,Thanks for the better picture of the meter. I wondered why the OP was measuring DC current. https://data.kleintools.com/sites/all/product_assets/hires/klein/mm300_photo.jpg gs5556 theory makes sense to me. I just thought the DC voltage at the o... | |
| Who Makes A Good Duplex Wall Outlet You can’t beat this outlet for the price.https://www.ebay.com/itm/NEW-HBL-8300HI-20A-125V-2P3W-HOSPITAL-GRADE-DUPLEX-RECEPTACLE-IVORY-NEMA-5-...It is a NOS Hubbell HBL8300H hospital grade outlet. It’s the real deal.Non plated brass contacts. A non... |