dover
Responses from dover
| What's your favorite $5-7000 turntable? Depends on your wall shelf - how much weight it can carry. Best lightweight option Rega P10 -complete package - under $7k - outstanding product. If your shelf can take weight - Sota Saturn with vacuum and Eclipse $7k Agree Kuzma R is very good ... | |
| SUT - electrical theory and practical experience Dear @dover : Yes I did it during the " thousands " of tests with the prototypes of the phonolinepreamp and through measures and listening tests the only parameter we can been aware was changes in SPL but not in FR but additional to that normall... | |
| SUT - electrical theory and practical experience @holmz this one - whether they generated a square wave with the same output impedance as the cart and fed the SUT with that | |
| SUT - electrical theory and practical experience My point about conjugating the imaginary (reactive) impedance of the cart is to cancel out any inductive or capacitive reactance so the cart sees a purely resistive load which will give the flatest frequency response with no peaking at high frequ... | |
| SUT - electrical theory and practical experience For some years in my system the active high gain phono stage came with a 100 ohm input resistor and through all those years I had not any single trouble ( that I been aware of. ) with several and different LOMC cartridges that I owned and own. ... | |
| Best Alignment Protractor? @cleeds As I said I have an Eminent Technology set up jig ( protractor ) that locks to the turntable spindle and bearing housing on the arm. It has a scribed line to set the stylus tip to. It is very accurate. http://www.eminent-tech.com/techsu... | |
| Best Alignment Protractor? Parallel tracking arms also require alignment. Azimuth, VTA/SRA, overhang. No overhang on a linear tracker. My Eminent Technology "protractor" is clealy more accurate than for any pivoted arm I have seen - you align the stylus to a very fine s... | |
| SUT - electrical theory and practical experience @pindac You do realise that everything can be demagnetised , including the phono, preamp stages and power amps - all with subtle gains. If you are going down that road, to the nth degree, - have you checked all your electronics for polarity ( r... | |
| SUT - electrical theory and practical experience @intactaudio One "gotcha" many people run into is dynamically overloading the input of the phono. With the current trend of higher output cartridges like the Atlas being paired with the typical 1:20+ SUT intended for LOMC's I see this type d... | |
| Grado Epoch 3 @dogberry Well done - my philosophy is if one has made no mistakes, then one only knows half of what they should. It's a good reminder that the cutting angle of records can be all over the place - hence pays to use a few well known records to d... | |
| Dynavector XV-1s What is the REAL story? @labpro Well done - a great example of just chipping away rather than throwing the baby out with the bathwater. The most rewarding systems are built with careful matching and set up rather than wholesale changes. | |
| High Performance Low Mass Tone Arm Suggestions Needed Moerch DP6 is the obvious arm if you want low effective mass - the 9" green dot arm tube is 4.5g effective mass and the red dot arm tube is 7.5g effective mass. | |
| Grado Epoch 3 I asked Grado about the proper load. Their position is that MM and MC settings are false and foolish. That the only way to set the cart is to try different settings to find which sounds best. Quite right. It has nothing to do with MC or MM -... | |
| Grado Epoch 3 The resistive loading is pretty much like a tone control that tries to flatten the response curve. 47kΩ lets the high notes predominate, so the cartridge is detailed but scratchy. Only in your system. At 47k the cartridge is flat - so you eithe... | |
| TechDAS Reliability vs SME @chauncey I've had both the Sota and SME 20 in house. The SME 15 would be a downgrade, the Sota is on a par with the SME 20. If you want SME you really want at least the 20/3 or a 30. The Techdas is a rehashed Micro Seiki 8000 - which some stil... |