2. amps-preamps
  3. 151715-109442

What type of Amp for Ohm Walsh F-5015s?

AudigoN Team,

Looking for some thoughts on amplifier choice for Ohm Acoustic F-5015 speakers that I will be getting shortly.  Would these sound better with a class D amp or a class AB amp? 

I have some space restrictions (17 inch deep open wood shelving with a back wall) that are limiting my amp choices absent a furniture change and I don't want to do that unless totally "painted into a corner"  John, the owner of Ohm told me that I should have at least 200 watts at 6 ohms to power the F-5015s.  The powered subwoofers built into these speakers come with class D IcePower amps with line level inputs, so the amp that I obtain must have two line level subwoofer outputs.

The two units (2 line level subwoofer outputs, 200 watts around 6 ohms, less than 17 inches deep, don't run hot) that have come up in discussion with John and Evan at Ohm are the class D NAD M32 and the class AB Parasound Halo INT6.  I have read that the INT6 doesn't run too hot, so it hopefully would be ok in a piece of wood furniture.  After my discussion with Ohm, I saw that the class D Peachtree Nova 500 could possibly work based on the specifications, but can't seem to find any reviews on this higher power Peachtree amp.  Another wild-card that would be much more expensive and offer higher power output would be the NAD M12/M22 v2 combo.  I am aware that you likely get what you pay for and that the NAD systems are higher priced, especially the non-integrated combo.

Would appreciate your thoughts / amplifier guidance and any additional suggestions.
michiganbuckeye
mapman's avatar
mapman
21,915 posts
 
Those two recommemded amps are probably available from reputable online dealers with a good return policy if needed.  Checkout Crutchfield, Audio Advisor etc. Maybe others can suggest one. 
dep14
336 posts
 
While OHM's love power (and I agree) with the 5015's I believe the can's will be cut-off at 80hz and those class D amps will push the subs nicely.

I've been quite surprised how the OHM's really do showcase different amps.  I happen to have a Pass Labs 250.8 and it really does work great with the OHM's.  I would take advantage of demoing amps to see what you really like.  

I've had a few amps in the system and it's amazed me how different each have sounded.  Good luck, those speakers you have on the way are beasts!  What finish did you go with?
michiganbuckeye OP
17 posts
 
Dep14, I am picking the rosewood finish and the version that has the smaller upper grills and the wood veneered middle portion above the large veneered tapered base (not the other available version with large upper grills like on the original Ohm Fs). I am having a pair of Ohm F’s that I inexpensively obtained remade into these by Ohm Acoustics, as the discount for reusing old speakers is significant.

Of the amps that I listed, 2 are class D and 1 is class AB. The amp you use is class AB. I have read that class D amps work best with "warm" sounding speakers and I have seen some Ohm speaker reviews that use the term "warm" in the description and some that do not include this word. How would you or anyone else reading this classify the Ohms that you have?

You may be amazed by this, but this is a totally blind purchase by me, so I don’t have any experience with Ohms other than a few minutes listening in an aisle way in a used audio store to a very old smaller pair with dated drivers. I am going off of online recommendations to my past posted topics, so all of you that have responded in the past collectively have picked these for me. Thus, keeping up with the spirit of this, you all can collectively help with the amp selection, which I may or may not, as stated earlier in this topic string, be able to audition prior to purchase.
mapman's avatar
mapman
21,915 posts
 
They will sound different with different amps.  

I'd say both of my current Ohm Walsh speaker pairs are neutral sounding. 

 I have Ohm F5 series 3,  which are similar to yours but one generation older model and no built in subs.   The 4 3 way level adjustments on each provide a lot of flexibility with tuning the speakers to teh room and personal preference. I run these off Bel Canto ref1000m monoblocks fed by an Audio Research sp16 tube pre-amp which perhaps adds just a touch of tube warmth.

I also have "Super Walsh 2 100 series 3 which are 8" 100 series 3 drivers in refurbed Walsh 2 cabs.  I use those with a Bel Canto C5i integrated amp.  This is perhaps the smoothest, most neutral, airy and detailed sound overall I have ever had.

Both  amps are Class D and I am a big fan of Class D amps with the OHMs for overall value and performance.   
joekapahulu
240 posts
 
I have Walsh Super2 100S3 units like mapman. I power mine with ATI 1502 amp which delivers 150wrms into 8 ohms estimated 180 to the 6 ohm speakers. I have previously run them with a Marantz pm8005 about 90 wrms. Both worked fine but I  like separates and use an upgraded preamp which is detailed but not harsh. Both are AB amps and sound good. I have run them with tubes too and they sounded good bjt were too hot for my climate.  All amps sounded different. I would try to get some trial amps to see what you like. I have heard the Hint and really liked it. I spoke to John at Ohm when I bought my speakers and he recommended a solid state amp with good current. The Hint provides that. I am not a class D guy but have heard good things about Wired For Sound amps. There is a very long thread on Ohm speakers on tnis site. You might scan that and see what amps others are using.
More to discover