CARY -- WHERE ARE THE CHECKS AND BALANCES?


Following is my abysmal experience with Cary Audio’s customer service and technical support.

Last year I revamped my system. After researching and comparing phono preamps, I picked up a Cary PH-302 MK1 and wasn’t disappointed. It produced the sound I wanted. Around this time I replaced my amp with an ARC Ref 110 with KT120 tubes that was approximately half as powerful as the old one. Afterwards when spinning vinyl for lack of a better expression was “running out of amp” -- meaning that when I cranked up the volume, I couldn’t get to where I wanted to because the gain on the MK1 is 38dB for MM and 54dB for MC. I didn’t have this issue with any of my other gear: all had much higher outputs.

I contacted Cary regarding the above and received an email from Jam Somasundram, Director of Engineering and Product Development. He stated that the gain could be increased and “highly recommended” converting my MK1 to MK2 status. I received another email from Dan Wemmer, Service/QC Manager, quoting the cost to increase gain by 6dB would be $200 plus shipping -- to upgrade to MK2 was $800.00 plus shipping (approx. $85 each way). The upgrade consisted of a new face plate, new chassis that added to the back switchable loads for MC cartridges, new manual, and increased gain to 60dB for MC cartridges. In other words my old unit would be the same as the current model. I was planning to switch from MM to MC so it made sense.

I sent my PH-302 the first week of August 2011 to Cary for the upgrade to MK2.

I got it back the first week of September. I replaced my Grado Reference 1 with a Soundsmith Paua.

The Paua wouldn’t dial in properly with the MK2’s preset loads. I contacted Soundsmith. Peter Lindermann suggested changing two of the presets to 1k ohms and 2.5k ohms.

I sent my PH-302 MK2 back to Cary at the end of October 2011 to have the loads changed. Cost $132 plus shipping ($85 each way).

It came back in December. The 2.5k ohm setting really brought the Paua to life, but disappointingly I was still suffering from too little gain. I was a bit discourage because so far I’d spent $1262.00 on the Cary alone and had only achieved dialing the cartridge in. I still liked what the Cary brought to my system and had invested more than I’d intended to. I needed to see if there was another solution to increase the gain in my phono section before taking a bath and replacing with another phono pre.

For the next few months, I researched various ways to increase gain. I sent queries to SUT manufactures, Soundsmith, and various others who do mods and upgrades to audio gear. There were lots of ideas but no consensus.

In April, I ran across a thread on Audiogon of a member in Australia who had modified his PH-302 MK2. I got in touch and we exchanged emails. I got the notion that if I upgraded the electronics this would improve the sound and the gain issue might be mitigated.

I’d read glowing reviews of mods performed by Chris Johnson’s company Parts Connexion in Canada. I got in touch with Chris, outlined my issues like needing more gain, related that Cary had raised it to 60dB when my unit was upgraded from MK1 to MK2, and wanted to take my PH-302 to the next level in the hope that this would assuage my gain concerns. Chris said Parts Connexion would check my PH-302 MK2 out and see what could be done. I shipped it to them in May 2012.

The first email I received from Chris was to report that the MC output gain was 52dB not the 60dB that I’d stated Cary had raised it to. I asked him to recheck to make sure because I had a hard time believing that it hadn’t been changed. After all Cary had serviced my unit twice. Chris emailed back that it was 52dB.

In early June 2012 I sent Cary a letter expressing my dismay along with documentation of my dealings with them to increase gain. Included were the emails from Parts Connexion detailing the actual output. I also stated that I’d wasted a lot of my time and others trying to resolve the gain issue because Cary had failed to do the job.

A week or so later I received an email from Steve Witek Cary’s Quality Service Manager. He was gracious enough, apologized, said that mistakes unfortunately happen, and then laid the blame on me for not notifying Cary that Cary hadn’t done the work. Why had I waited 11 months?

I was kinda floored, I emailed back to Steve and asked how was I supposed to know that Cary hadn’t done the job. I don’t have that kind of diagnostic equipment. Isn’t Cary the expert here? I pointed out that my PH-302 MK2 had been serviced twice by Cary. One of my questions to Steve: why hadn’t it been bench tested either time to assess if it was performing to factory specs. My experience has been that testing gear is one of the first priorities other manufacturers undertake before anything is done.

Throughout our email exchanges, Steve never acknowledged that Cary had serviced my PH-302 MK2 twice. He only ever referenced the August 2011 date. Nor did he ever answer my questions as to why my unit was never bench tested before or after the work was done. If the quality service manager can’t answer this, then who can?

Steve’s next response was to cherry pick the emails that I’d sent him in an attempt to concoct a scenario that I’d known all along that Cary hadn’t done the job and was going behind their backs to other companies.

To circumvent the above, I forwarded the emails I had sent to Parts Connexion regarding this issue in which I explicitly stated my belief that Cary had done the job.

Steve’s reply was not to acknowledge the point of these emails, but again resorted to cherry picking: he pulled out the price estimate from Parts Connexion of $100 to rewire to achieve the 6dB gain. Steve decided this to be the amount that Cary would reimburse me for the work that they had failed to do. He didn’t bother to take into account the $1262 spent on the PH-302, time lost, or CARY’S ORIGINAL ESTIMATE OF $200!

I emailed expressing my irritation, disappointment and pointed out to Steve that he “didn’t seem to take responsibility for anything.” In that same email I included:

“A good piece of gear is only one part of the sum. Quality reliable support is just as important. At least it is for people like me who buy for the long haul and look for ways to obtain and insure maximum performance.”

Where were the checks and balances?

Would I have purchased the PH-302 knowing what I do now, NO. Do I still feel that it is a good piece of audio gear: YES. Will I consider purchasing other Cary products, NO. The reasons being that there are plenty of manufacturers out there that offer equally good products along with exemplary service void of excuses who do the job right the first time. I know this because of first hand experience.

Did I accept the $100 restitution -- NO

Like stated at the beginning, this is my experience dealing with Cary Audio. I know there are a lot of satisfied Cary customers. It was my intent to join those ranks. If you are someone contemplating purchasing a Cary product, then I hope this serves as a cautionary tale.

Has anyone had a similar experience as mine?

Regarding the MC output issue. Parts Connexion raised it from 52dB to 58dB which totally took care of this problem. I’m spinning vinyl now with a huge grin. Chris and his engineer did a bunch of other mods and upgrades. THEY DID AN AWESOME JOB!!!!
128x128fossilsx15
I was in contact with a tech about six months ago and he was extremely helpful and always answered my questions concerning my SLI-80F1. I hope this isn't the case concerning Cary's customer service as I like their classic products. This is the sort of thing that can bring a company down.
Bombaywalla

I have known Billly for almost 20 years I consider him a honest, forthright and stand up guy. I have dealt with Cary for as long and the few times that service was required it was always handled in a timely and expeditious manner.

What I'm stating above is from personal experience and not form what others are telling me - I would never publish negative statements about anyone form hear say - to me that's just not the right thing to do.

Roxy - I don't know if Mr. Rankin is still with Wavelength - I would assume as I have not heard otherwise.

Really appreciate everyone taking the time to post their comments. Very nice to be a member of such a passionate community!

Unfortunately this proves that Cary has some serious QC and CS issues to resolve.

I couldn't imagine posting or reading a thread like this of the other manufacturers that I deal with or have had dealings with like ARC, Grado, Soundsmith, Tyler, Rogue, Modwright, and Thor.

Like Brownsfan posted: I also hope Cary is paying attention to threads like this. A company does need to take care of its customers especially in such a tight knit one as audio.

Thanks again,

Brian
The truth is only a couple of people who contributed to this thread had direct interaction with Cary that was injurious to them. Unfortunately the experience of a few is not always the experience of the majority, but get broadcast. Maybe I am naive and giving them to much benefit of the doubt. It is difficult to assess what is really happening with most people.
The one thing I know is that their products have limited distribution and dealers here in the USA. I knew one dealer in PA that couldn't compete with Upscale Audio who evidently enjoyed discounts (possibly volume) and exclusives. I haven't looked in a while now to see who else is selling new.
Part of the problem may arise from people buying used and then needing service. I can see how that would be an issue for manufacturers in better audio these days not just Cary.
Part of the problem may arise from people buying used and then needing service. I can see how that would be an issue for manufacturers in better audio these days not just Cary.
Mechans
how exactly is this an issue, Mechans?
IMO, it should not be an issue. All manuf know that their product is not going to be with the original owner during the product's entire life. If they did, they/manuf would be stupidly naive! So, the manuf obviously have a warranty plan that takes into account that their products continue to give good service/output when sold several times over. The manuf warranty is either transferrable or not. If a unit that needs service is out of warranty have the present owner ship it to the factory, factory takes a good look at it for a nominal fee, diagnoses the problem, suggests the fix & quotes the $ amount for the fix. Then the factory should honour their word & do what they said they'd do for the money they said they'd charge. Once repairs/service completed, ship the unit back to the owner @ owner's expense. That's it - we're done. Both parties are happy & it's win-win. Not the crap that Fossilsx15 went thru!
If the unit gets severely damaged during multiple sales, so be it. It'll take more money to get it fixed. Factory quotes the higher fee to fix a badly damaged unit & the present owner decides if he/she want to engage.
I'm not seeing the issue, Mechans.....
Is this repair of a unit supposed to be any more complicated?