Try placing the block on some isolation devices such as cones. If the block is sitting directly on the cabinet it will transfer vibrations to the table. Isolate the block from your cabinet as well as you can.
Weak/tubby bass on old Philips 212 TT
I have an old Philips 212 electronic TT that I have been restoring. It has new lights/sensors, a new belt, and a new Grado Prestige Blue cartridge.
Replacing the belt made a huge difference as the old one was either too big or stretched out compared to the replacement, resulting in poor speed control and PRAT. Now with the table placed in my cabinet on a heavy wooden block, I'd have to say the sound in the mid to upper registers is really good with depth and air around female vocals and guitar, and good pace. Not the nth degree of high treble extension, but detailed and sweet lower treble and midrange - surprisingly good compared to Rega P2 and P3 tables I have been auditioning recently with stock Rega cartridges.
But the bass from the Philips just isn't up to the same caliber as the higher registers. It is weak and a bit tubby through both headphones and speakers compared with the two Regas mentioned and my Cambridge Audio CD player. Not terrible, but now clearly the weakest part of the overall presentation. I am a bit surprised by this because Grado Prestige cartridges have a reputation for relatively strong bass for the money.
The cartridge is aligned as close to square in each direction as I could desire without shimming - the tonearm's fixed VTA results in the cartridge being tilted a bit up at the front - a condition I would think would increase the bass response relative to rest of sound spectrum. I adjusted the overhang with a protractor. The cartridge is set to track at the recommended 1.5 grams and the anti-skate is set for an elliptical stylus, although adjusting this a little either way makes little difference in the sound. I am using the MM phono preamp on my AMC 3050a integrated amp with some minor modifications (12 gauge power cord and high quality plug, HiFi Tuning fuses, silver jumpers).
Question: are there any simple tweaks I can try do to improve the bass response on this table/arm/cartridge combination? I realize the arm is not the last word in rigidity with it's plastic cartridge insert, and I am suspecting that is where the problem lies. Any suggestions appreciated short of "get another table".
Replacing the belt made a huge difference as the old one was either too big or stretched out compared to the replacement, resulting in poor speed control and PRAT. Now with the table placed in my cabinet on a heavy wooden block, I'd have to say the sound in the mid to upper registers is really good with depth and air around female vocals and guitar, and good pace. Not the nth degree of high treble extension, but detailed and sweet lower treble and midrange - surprisingly good compared to Rega P2 and P3 tables I have been auditioning recently with stock Rega cartridges.
But the bass from the Philips just isn't up to the same caliber as the higher registers. It is weak and a bit tubby through both headphones and speakers compared with the two Regas mentioned and my Cambridge Audio CD player. Not terrible, but now clearly the weakest part of the overall presentation. I am a bit surprised by this because Grado Prestige cartridges have a reputation for relatively strong bass for the money.
The cartridge is aligned as close to square in each direction as I could desire without shimming - the tonearm's fixed VTA results in the cartridge being tilted a bit up at the front - a condition I would think would increase the bass response relative to rest of sound spectrum. I adjusted the overhang with a protractor. The cartridge is set to track at the recommended 1.5 grams and the anti-skate is set for an elliptical stylus, although adjusting this a little either way makes little difference in the sound. I am using the MM phono preamp on my AMC 3050a integrated amp with some minor modifications (12 gauge power cord and high quality plug, HiFi Tuning fuses, silver jumpers).
Question: are there any simple tweaks I can try do to improve the bass response on this table/arm/cartridge combination? I realize the arm is not the last word in rigidity with it's plastic cartridge insert, and I am suspecting that is where the problem lies. Any suggestions appreciated short of "get another table".
7 responses Add your response