Taming the high frequency

Good!  No more ear bleed.

Problem solved by rearrnging some decor and furnishings. Thanks to all who had suggestions.and gave their opinions

Two things have helped  me , put a blanket over any TV in the room and
 turn off your wi-fi .

I've found that harshness can be from various factors.  One thing you can try for cheap is to listen off axis (i.e., point the speakers ahead instead of towards your ears).  Also, quality of power can be relevant as well, you might want to look into power conditioning - I found that something like the Shunyata Denali definitely makes a difference.  With regard to your room treatment, I don't see anything that indicates that you have treatment at the first reflection points on the side walls or ceiling.  Also, I assume you have a think rug or similar covering the floor from the speakers to you because that's important as well for reflections.

Thank you all for your input. It's all well received and valuable. I was hoping for room treatment correction if possible as that is the least costly but........
I will try an old standby solid cable to see if there is any improvement.........or not since it is already available. Lord I hope I can stay out of the cable experimentation scenario.

@gillatgh - what speaker cables are you using?.

Your amp looks like a high current design?

If so - it may be experiencing an oscilation reaction with the speaker cables - i.e. if the cables have a high capacitance value it will staret oscillating - which will impact the sound

Selecting a speaker cables that has a capacitance of 10-20 pf/ft should eliminate the high frequency oscillation - if this is the problem

Van den Hul D352 or NAIM NAC A5 are two affordable cables that are low capacitance in the 10-15 pf/ft and they are pretty good performers.

By comparison - Cardas Golden Cross has a capacitance rating of 154 pF/foot.

A friend drove both his Ayre and Gryphon amps to destruction using high capacitance cables - not good.

Solid State amps having a High Current design will have this issue - whereas tube designs WILL NOT have an issue with high capacitance cables.

For high quality/resolution cables that will work very well with high current designs take a look at the KLE Innovations product line. I have reviewd many of theri products and they are first class and they work extremely well with my NAIM 5i - also a high current design.

Hope hat helps - Steve

Can’t the Lexicon be adjusted to tailor the sound? Looks like it has all sorts of settings. Reading around, I see a comment about it being harsh. The Adcom is pretty bright and B&Ws can be a bit up there too. And it’s a digital source. If no good results from adjustments, try your rig without the Lexicon.

Ghost, thanks for your input. Thinking about it even with the Krell there was some harshness at certain high frequencies regardless of the source. It is possible that the Lexicon is more adept at identifying the problem. I’ve never used any room correction software and may have to try that. Someone else also mentioned cardas to me. It may be a solution.. ... yes all been in use a loooong time. This is very frustrating.

Tissue paper over the tweeters a la Yamaha NS10s in the studios back in the day!

I fought harsh for a long time. First recommendation I’d have made was room treatment...but you have that pretty well covered - unless there is further benefit to be gained by replacing the decorative blankets behind the speakers with a couple of GIK panels. I found a Hegel H200 SS integrated to be significantly warmer than the 6CA7 tube mono blocks I had. Cardas ICs and speaker cable helped a lot too. A good deal of the pain and "gambling" with wire can be eliminated by borrowing from the Cable Co. I didn’t understand what you are using as a source...any chance this is contributing (or did it sound fine when the Krell was in service)? Finally, I assume everything is well broken in? Final thought is to consider some sort of equalizer.  Some here are very happy with the Schiit Loki.  

Good luck!

Noromance, I'm not sure a tube amp can provide the umph I require unless I win the lottery, so that's a real stretch. Yep, dug out my collection of speaker cables, audioquest, straightwire, transparent, blue eans and JW solid core. Tried them all with no noticeabl difference. Can't say I've ever heard of Audio Sensibility Impact interconnects. Loom of interconnects is all audioquest. I appreciate your reply. I really hope I don't have to go thru the cable witch hunt again. I'm hoping that some form of room treatment or correction can solve my issue. It' also not at all high frequencies just certain ones.

Consider replacing the Adcom for a tube power amp? Solid core speaker cables? Duller interconnect like the Audio Sensibility Impact?