REL G-2 Question


I recently purchased a lightly used REL G-2 sub. (This is first sub I've ever owned.) It sounds great but there is one operational issue that has stumped even REL's engineers at their office in California. I do mostly 2 channel music and my system consists of Sonus Faber Liutos, CJ ET3-SE pre, McCormack DNA 500 amp and Esoteric X-05 CD player. My HT system is an older B&K 305 receiver with a Luito center channel. I use the Theater Bypass on the CJ to connect to the B&K so I can get 3.1 Dolby digital when watching TV or using my DVD player. I am using the REL's high-level connections to the McCormack and the .1 LFE connection from the REL to the B&K. All connections have been made exactly to REL's recommended set-up and connectivity directions.

Here is the problem: When in 2 channel mode, the REL's separate .1LFE volume control will actually supply gain to sub when there is no LFE signal! I even unplugged the B&K from the wall. Raising the LFE volume still creates gain! I then tried unplugging the interconnects from the CJ's theatre bypass to the B&K. This does not eliminate the gain either. The only way to eliminate the volume gain from the LFE is to unplug the actual .1 LFE cable from either the REL or the B&K. I can, of course, set the LFE volume to Zero and control the sub's 2 channel music volume through the High Level volume control just as it is supposed to work. It bothers me though that the sub is performing in manner in which it was not designed to perform. I've talked to dealers and to REL's engineers on the phone and no one can figure out what's happening. They all state that they have never heard of such a thing and that it seems impossible. One said it sounded like cross-talk so I made sure none of the cables were touching each other and made sure no bare wires were touching each other.

In closing here are my questions: (1) Do any of you know what might be happening? (2) If any of you have a G-2 (or G-1) would you mind turning up your LFE volume while in 2 channel mode with a similar LFE connection and let me know if you get the same result? (3) If the sub performs flawlessly in all other areas is this even worth worrying about given that I can just unplug the LFE cable when listening to music? BTW: The seller has offered a complete refund if I want it.

THANKS!
shoff
All I can say is that both inputs provide volume controls 1 has to be down while your using the other. Does this still occur with 1 of the volumes all the way down? Can you turn 1 off while using the other by just lowering the volume for that input on your remote? If this is not the case, then your REL has a problem and needs to be repaired. I have a REL B2 Britania series and its the best sub I have ever heard. GO REL!
Matt,

Thanks for chiming in. If I set the Hi Level volume at zero, I can dial up the .1 LFE volume and it adds gain to the sub even though there is no LFE content present. This is in 2 channel mode. It is my understanding that you are supposed to be able to set the LFE volume and leave it there for HT use and not have to worry about it during 2 channel use because it is automatically filtered out. Then, when listing to HT and .1 content is available you get a "double dose of bass" (the .1 content + the Hi Level augmentation from the main speakers).

In answer to your other question, yes, I can turn one off while using the other just by lowering the volume on the remote. My next diagnostic is to see if I can find another G-2 owner and insert his sub into my system and see if it acts the same way. If so I'll quit worrying. If not I'll seek a repair. Thanks again for your input.
After reading the owners manual it looks like you have to adjust the volume down for the 1 your not using. I get what your saying tho. It is kinda strange in 2 channel mode it still picks up the HT. But I think it is not broken.
Thanks again Matt. I think you are correct that the problem is not with the sub, even though in talking with REL's engineers they say you should not have to turn down the LFE while in 2 channel mode. Instead, I believe the problem is a "phantom signal" created by the .1 LFE connection between my B&K AV receiver
and the REL even though the unit is turned completely off. I was not smart enough to think of this but a B&K dealer was! I'm trying to plug another G-2 into the system to check out this theory.
Sorry.. I wasn't trying to be a D**K Personally I'd just use the REL's high level input and be done with it, since it's likely to sound best that way anyhow.. My REL certainly does.