I purchased a Rega Planar II 35 years ago and applied the following upgrades over that many years ...
- sub platter/bearing ball - all metal/ceramic
- platter - acrylic
- motor - latest version from Rega
- counter weight - Michell Techno-weight
- arm - installed a one piece harness, but eventually installed an Audiomods arm
- plinth - high mass plinth (as opposed to Rega’s low mass plinth design
- various isolation tweaks
If you have not made too many upgrades to date then I believe upgrading the turntable would be more prudent.
The Audiomods arm was perhaps the most effective, but most expensive upgrade, but I believe that its performance would not be as good if not for the plinth/platter/sub-platter upgrades also. They are so dependent on each other that failing to implement any one of them would impact the overall performance.
I am a huge fan of the Audiomods arm and when coupled with the right cartridge, in my case a Soundsmith modified Denon DL 103, it provides exceptional performance.
In it’s day (i.e. 35 years ago), the Rega line was a huge step forward in TT design, but the rest of the industry has found various new design approaches, technologies and materials that level (or surpass) what Rega has to offer in the same snack bracket
The cost of all the upgrades exceeds some very nice TT’s on the market today.
With each upgrade I acquired more knowledge about Rega's TT design (and flaws) and it drove me to pursue more effective isolation tweaks, so that was a benefit of the upgrade path..
One plus - Rega TT’s probably has the larget selection of after market upgrades available, so the choice is vast
On the negative side, you will probably not maintain your Rega’s resale value
Can your Rega be bettered? - of course, by either upgrading or replacement. It’s just a matter of how much time/cash you are willing to invest in. The determination of which upgrade is best also requires considerable anaylsis.
If I had to replace my turntable today i would probably opt for something from the VPI lineup.
Just another opinion :-)
Regards - Steve
- sub platter/bearing ball - all metal/ceramic
- platter - acrylic
- motor - latest version from Rega
- counter weight - Michell Techno-weight
- arm - installed a one piece harness, but eventually installed an Audiomods arm
- plinth - high mass plinth (as opposed to Rega’s low mass plinth design
- various isolation tweaks
If you have not made too many upgrades to date then I believe upgrading the turntable would be more prudent.
The Audiomods arm was perhaps the most effective, but most expensive upgrade, but I believe that its performance would not be as good if not for the plinth/platter/sub-platter upgrades also. They are so dependent on each other that failing to implement any one of them would impact the overall performance.
I am a huge fan of the Audiomods arm and when coupled with the right cartridge, in my case a Soundsmith modified Denon DL 103, it provides exceptional performance.
In it’s day (i.e. 35 years ago), the Rega line was a huge step forward in TT design, but the rest of the industry has found various new design approaches, technologies and materials that level (or surpass) what Rega has to offer in the same snack bracket
The cost of all the upgrades exceeds some very nice TT’s on the market today.
With each upgrade I acquired more knowledge about Rega's TT design (and flaws) and it drove me to pursue more effective isolation tweaks, so that was a benefit of the upgrade path..
One plus - Rega TT’s probably has the larget selection of after market upgrades available, so the choice is vast
On the negative side, you will probably not maintain your Rega’s resale value
Can your Rega be bettered? - of course, by either upgrading or replacement. It’s just a matter of how much time/cash you are willing to invest in. The determination of which upgrade is best also requires considerable anaylsis.
If I had to replace my turntable today i would probably opt for something from the VPI lineup.
Just another opinion :-)
Regards - Steve