Krell KRC-3 Questions


Couple of questions for any KRC-3 owners out there: 1) do you leave your KRC-3 on all the time? and 2) can you recommend a cd player with balanced ouptuts (I am prepared to look at new mid price and used high end). System is KRC-3, KAV250a with Celestion A3's, Kimber PBJ interconnect for pre-amp to amp (need to upgrade - any ideas?) and Van den hul cs122 speaker cable ( bi-wired). At present using an old Cyrus CD6 as source and I must say sound fabulous but clearly source is weak link.

thank you

Paul
paul_smith
i owned a krc-3 for ~8 years & was sad to let it go recently. It's a very good pre-amp. I found it to be quite nuetral, letting source components sound, well, the way they sound ... good or bad.

i left mine on all the time, except for when i knew i would not be listening to it for extended periods of time. i shut my whole system down. as u know, the krc-3 doesn't come with a power on/off button so i think krell designed it to be left on all the time. i found it sounded its best, like the krell amplifier i also owned, after they'd been "cooking" for some time, at least 24 hrs. it runs hot so leave lots of room around it.

the krc-3 sounded its best when connected with balanced cables to the amplifier. i used MITs.

good luck.


IMO, used Krell KAV300 CD would be a nice match. You have to get rid of those horrible ICs and speaker cables though !

Get an used pair Cardas Golden Reference ICs (400$ on AudiogoN) and some decent speaker cables (like AudioQuest CV-6).

And yes, I leave my KRC-3 on all the time.
Hi Paul, I have owned the KRC-3 and the KRC-HR before. Just one point. The KRC-3 sounds better with the gain on. I agree with Elberoth2. You need better interconnects and speaker cables.
Pictura,

What is your opinions about the sonic difference between the KRC-3 vs. KRC-HR?

Richard
thanks for the responses - yes IC's/speaker cable are not ideal! - was using KS-1010/1011 from a meridian processor but felt balanced inputs on KAV250a gave better sound and I was not happy with using a processor as a stereo pre-amp.Now eith HT bypass I get the best of both worlds.Still a work in progress.... but have to say much happier with combining stereo/HT systems
Sorry if this is late, but I have had a KRC-3 for around seven years or so, though four years of that the pre has been boxed (unused). It has been up and running for more a couple of years now though, feeding an Aragon 8008BB. Since the KRC-3 has no power switch, I have always just leave it on, turning the volume all the way down when not in use.

I own and can recommend the Arye CX-7 CD player (not yet Evolutioned). I was previously running the CX-7 and KRC-3 with MIT Z Cord II power cords, with an LAT International AC 2 cord feeding the 8008BB amp. I purchased three of the promotional Shunyata Snakebite power cords, and now use them on an AudioPrism power strip, KRC-3 and 8008BB. I switched the LAT power cord to the CX-7. This works better than my previous power cord setup.

Like others, I have tried many different interconnect and speaker cables. Much depends on what you are seeking. I think I am searching for an accurate reproduction (within reason) of what is on the source CD, with no added distortions or noise, etc. I am using and like a balanced pair of Straight Wire Serenade between the CX-7 and KRC-3. It is not anywhere near the most expensive cable I have tried there (it retails for $350 per meter pair), but works very well. My dealer thinks I would prefer the Virtuoso R (or whatver the current letter designation is), but I have not tried it.

I did try the Virtuoso R speaker cable, internally biwired, and it is the only cable that has significantly bested my resident MIT MH-750 biwire in all areas. I have also tried an internally biwired set of Serenade speaker cables, and although it was very good, easily besting the MITs in many areas of performance (treble, midrange, tone, timbre, neutrality too I think), I thought it a little weak in the very bottom of the range. Maybe it was just neutral there, but I doubt it. More likely is that I would need a double run (shotgun) of the Serenades to my speakers instead of an internally biwired run.