But it is the act of removing the LP from its paper sleeve that does the most to generate a charge on its surface. So you would have to zap it again, once you removed it from the paper. Which makes it a waste of time to zap it in the sleeve, even if that does work.
Found a Milty Zerostat alternative
I was thinking about buying the Milty Zerostat but came across a discussion regarding this plasma arc lighter.
https://www.amazon.ca/Lighters-Electric-Rechargeable-Lighter-Windproof/dp/B09CYQ92PF/ref=dp_prsubs_sccl_3/130-2888405-1836766?pd_rd_w=YAj0t&content-id=amzn1.sym.7f829f53-1df3-4cd3-91bf-9933c19106a6&pf_rd_p=7f829f53-1df3-4cd3-91bf-9933c19106a6&pf_rd_r=XCDACDZA93ZQEQD27N82&pd_rd_wg=LfOt5&pd_rd_r=6ea7c5de-5354-4a91-9826-e178d9a2b653&pd_rd_i=B09CYQ92PF&psc=1
It really works well! I took a record out of it's sleeve and held a tissue against it. The tissue stuck to it, even when held upside down. I turned on the plasma lighter and held it about 1.5" away and made two or three circular passes around. Tried the tissue test again and it would not stick to the vinyl. It's also well constructed and doesn't feel cheap.
- ...
- 34 posts total
Long ago, far away.... I bought a Kilavolt No. 103 by Nagaoka... Rotate LP on platter. Hold Kvolt above LP, starting at 'run-out', press button and 'tangent out' in a spiral to edge. Apply carbon brush, center to out... What static? Mine's still going strong....if not, one new 'B' cell. Carry on....good luck finding one.... ;) |
ghdprentice, same with me. Constantly AFTER usings the Zerostat my TT felt matt sticks to the vinyl, and has to be placed back onto the platter.I also use it on the vinyl just before I use my carbon brush, hoping that it will make sweeping dust easier. It is also no help there.Recently I received a new record whose' plastic sleeve was so staticky that it was stuck to the vinyl like it had been vacuumed sealed. I zapped it with the Zerostat to see if the sleeve would loosen up and I saw no difference. Then I zapped the vinyl and empty sleeve and saw no change.Since it is useless I might dismantle it to see if I got an empty gun. |
Most likely you are using the zerostat incorrectly. There's no shame in that. Zapping an LP inside its wrapper or sleeve, whether paper or whatever, is never going to work. One reason your LP may stick to your felt mat is that felt itself is a good donor of negative ions to vinyl. But also, if you remove static charge from the surface of an LP with the LP held in the air OFF the platter while you zap it (the only way it works according to my observation), that takes care of the side you play only. The bottom side that goes against the mat will still be charged up to begin with. The Shure Corporation published a long paper on static charge many decades ago in which they showed that charge migrates from one side of the LP to the other, after you treat one side. Finally, when you are using the zerostat, with the LP in your other hand, pull the trigger all the way back with the gun held away from the LP. Then start with the gun near to the LP and very slowly pull it away while very slowly releasing the trigger, ideally so slowly that there are no "clicking" sounds. |
I too have a 50 year old Discwasher Zerostat that still works. I can check the operation with a small probe that consists of a 10 nf capacitor in parallel with a neon bulb. A wire from one leg of the capacitor/bulb circuit is held near the Zerostat output while operating it. A second wire from the opposite leg of the capacitor/bulb circuit is formed into a small loop that you can grip between thumb and finger. The bulb will briefly glow on the slow pull of the trigger and the slow release of the trigger. |
- 34 posts total