DIY do it yourself tube amp kit


Does anyone know of a really high end DIY tube amp company?
128x128keithmundy
Are OTL's good with low impedence electrostats?

At the crossover region of 125Hz, I think those speakers were known to drop down into the 2-3 ohm range. Not an easy load, at all.
I want to build a pair of Mono Block tube amps. I have a pair of ML Quest Z. What is your recommendation? I play my music loud and listen to all kinds of music. What do you think?
Darkmoebius, Yes, I spoke with Response. Sounds like they are very familar with the Hurricanes. I may check that out. I'm trying to keep my overall investment in my system lower than I have in the past. I've found that there are deminishing returns per dollar spent and am actually cutting back. Trying to get the best bang for the buck. Thanks for your correspondence.
Keithmundy,

Response Audio does extensive mods on the ASL Hurricanes, though it doubles the price.

If you can get by w/ 100wpc, they also do the same mods on the Monsoons.

Check out the listed changes they make to their amps for ideas.
thank you both for your input. I new I would need large amp to drive them. Hmmm? I just have this desire to try some tubes amps. I've auditioned the ASL Hurricanes and they did a good job - of course - no kit though. I may end up just buying a pair of Hurricanes and maybe play around with mods. Thanks again for your help.
Keithmundy
Darkmoebius is absolutely correct. Vandersteens and SET amps is not the way to go. I had Vanddersteen 3A Sig with a 100 watt tube mono amp and I ended up selling the Vands, to hard to drive.
Hi Keithmundy,

Sorry to bring this up, but only two of the kits mentioned so far will do your Vandy 5's the least bit of justice - the Velleman K4040 at 90wpc and the Transcendant BEAST at 165 wpc. In fact, the Welborne, Audio Note, other Transcendants, Decware, and Bottlehead amps should never even be considered.

My brother has Vandy 3A Sigs and they are a demanding impedence match. Even though the 5's have a built in 400 watt subwoofer amp, the 3 other drivers are still rated at 87dB w/ an impedence that fluctuates to 4 ohms.

You really want to look for an amplifier in the 75+ wpc range with a stiff power supply to do these speakers any justice. If it was me, I'd go 100+ wpc and there simply aren't many kits in that range.

Hell, the 5's have been known to cause the Audio Research 100.2 to run out of gas on large orchestral works. And that is a serious high-current solid state amp. My brother uses it to run his 3A Sigs.
Gbslps, thank you for your response. Audio Note is a great quality source! Cheers
Audio Note Kits have very high quality parts and varying price ranges. Preamps Amps Phono Dacs Speaker Kits
http://audionotekits.espyderweb.net/
What kind of speakers are you driving? That's the most important factor.

Decware, Bottlehead, and Welborne are best suited for speakers above 94dB efficiency with fairly stable impedences above 8 ohms.

I have Welborne DRD 300B monoblocks and they are stunningly transparent and revealing. The most "pure" 300B amps have ever heard. But, 7 watts per channel will only get you so far.

I have driven 90dB/4ohm Jean Marie Reynaud monitors with them and the combination was great for acoustic, jazz trios, and chamber music. But, larger scale, more demanding works would run out of gas.

Be sure to add Diy HiFi Supply's kits to your list. They have fanatastic low power amps and a 40W PP amp.
Check these out and dream away--
www.transcendentsound.com
www.decware.com
www.bottlehead.com