2. speakers
  3. 152695-20253

Bending wave, low order crossovers and tradeoffs

Stereophile just reviewed an interesting bit of kit, the Manger P1. The mid-tweeter is a bending wave transducer, while the woofer is conventional. Crossover point is around 400 Hz.

The DIY community has a similar type of design called Woofer Assisted Wide Band.  It is 90% wide-band, plus a woofer.

https://www.stereophile.com/content/manger-p1-loudspeaker-measurements

Of course, you have to listen to make any sort of real assessment as to the value of the speakers and their suitability to your own home, I just wanted to share with the measurement readers how I might look at a crossover and the paths not taken so others can gain some insight into just how much is happening in the crossover design of a speaker.  Let's take a looksie ...


There are many who feel the best crossovers are 1st order (6 dB / octave) as high order rob dynamics or something. This is not an effect I have heard. Lots of 1st order, time aligned speakers I have not like at all, and one with active woofer system, was spectacular. So for me this is not a compelling sales pitch.


But still, lets say low-order or no-order filters is a very desirable characteristic, so lets talk about the negative consequences of having a very simple crossover, as apparent here.


Comb Filtering
Those armchair speaker designers who get frothy mad at driver arrays, claiming "comb filtering" when there's no evidence in the measurements are oddly silent when it's right in front of them. This is a good example. Look at figure 5. Plenty of comb filtering visible here.  What's going on? The low-order filters used is letting the woofer interfere with the mid-tweeter. Lots of great speakers do much better off-axis than here.


Next, lets look at the impedance chart, Figure 1. See that 3 Ohm dip around 200 Hz? With a low rise above 8 Ohms around 1,500 Hz? This is evidence of a minimalist crossover. It's quite possible that the woofer is run full-range with no low pass filter at all, and the mid-tweeter may have only a cap.


I will say that I do not like speakers with a dip in this region, as I find them quite demanding of amplifiers. My usual reaction is "WHY WOULD YOU DO THIS?" and then I am reminded that audiophiles LIKE demanding speakers. We are rather masochistic when it comes to the care and feeding of speakers. Some manufacturers deliberately drop the impedance in this range for exactly this reason.


Lastly, lets look at the overall shape of the output, Figure 4, showing a subdued mid-range. Not exactly recording studio attributes here, but possibly a good speaker at lower volumes. The shape here is a function of the cabinet, drivers and crossover design. No one thing contributed to the speaker's tonal balance, which we can lay it the foot of the designer, but if you choose to use a minimalist crossover as evidenced here there's only so much you can do to change things.


So, to recap, the designer picked a minimalist crossover and accepted poor lateral response and a low minimum impedance, and a lumpy frequency response curve as trade-offs. Or we could say he/she wanted all three.




Best,

E
erik_squires

Showing 7 responses by erik_squires

erik_squires OP
16,468 posts
 
I'm probably going to offend people who actually know bending wave transducers, but I think the Ohm Walsh drivers are great examples.


In a normal cone, you want the whole thing to move, like a solid piston, but without the mass. :)  That is, ideally, the voice coil, dust cap and cone all move at exactly the same time.

The Ohm Walsh driver looks like a piston, but here's what's different: The cone bends. The signal starts at the voice coil and then, over time, travels down the length of the cone to the ends. I'm not even sure if the end of the cone is allowed to move or not, it may be fixed.

And to me this is the overall principle of a bending wave transducer. They are excited at one point, and then at some point in time the signal finally reaches the edges.

With a cone, ribbon, ESL, AMT the ideal situation, the signal reaches the edges of the driver at the same time it reaches everywhere else.

Of course, there are no absolutes, but that's the definition I work on.
erik_squires OP
16,468 posts
 
Here is the old thread we had on bending wave transducers:

https://forum.audiogon.com/discussions/gobel-and-the-bending-wave?highlight=bending%2Bwave
erik_squires OP
16,468 posts
 
Hey @twoleftears - Where were you when we were talking bending waves a few months ago?? :)



erik_squires OP
16,468 posts
 
So if the comb filtering is solely the result of the mid-tweeter driver, that implies at least 2 discrete surfaces with a significant distance between them, no?

How very peculiar.
erik_squires OP
16,468 posts
 
Kenjit:


I am not sure who you are talking about:

1 - Not sour grapes. As I said before, the value and sound quality of the speaker cannot be determined by specs or measurements.


2 - You’ve accused me of using 1st order crossovers before, and I’ve corrected you before. I have never designed a speaker with 1st order crossovers. Maybe you don’t know what that means?


3 - So JA writes a non-committal "they sound like they measure" sentence and you think that puts us at odds? No. JA is an awful and biased speaker reviewer, but this statement is so bland and nondescript you can’t possibly take its meaning.


Erik
erik_squires OP
16,468 posts
 
It is also showing no output greater than -40 db above about 3.5khz. How could it be running full range if this is the case? There would almost certainly be a lot of output above that with an unfiltered 8 inch driver.

Depends on the woofer, really. I imagine a custom unit could be built that way, or which needed only 1 additional component. Also, the output may seem low, but it is not too low to avoid interference. Could that comb filtering be caused by the bending wave transducer? Possibly, but then why is it different horizontally and vertically?

Honestly the shape of the roll off measured, the impedance and lateral measurements aren’t aligning very well. If it’s using a 2nd order low pass, then why is it interfering as much, and why is the impedance curve the way it is?

Perhaps 1st order filters? It’s hard to know without knowing the impedance of the original drivers.

Again looking at figure 3, this would appear to be all due to the bending wave driver with likely some cabinet contribution.

Right, and if you have a very simple crossover, you don’t have the ability to flatten any such shape, so you are left with whatever the driver starts with.

My point here was to reinforce something I said elsewhere, most crossovers incorporate some amount of equalization, but very simple circuits have to avoid them.

Though it can be said that even a 1st order filter, judiciously picked, can do both EQ and filter.
erik_squires OP
16,468 posts
 
PS - If you like the idea of a minimal crossover, may I suggest building the classic Seas A26 kit?

https://www.madisoundspeakerstore.com/2-way-speaker-kits/seas-a26-10-2-way-kit-pair-based-on-the-cla...

It has 1 capacitor and 1 resistor, and you can experiment by adding a 2nd order to the tweeter. Building a kit like this is a great thing to do with a friend or loved one you want to introduce to audio.


Best,

E
More to discover