williewonka
Responses from williewonka
Turn Table Decision If the above procedures did not workHere’s a quick debug procedure that might help...- get a length of wire - about 6 ft- attach one end to the ground pin only on a mains plug - strip about 1/8" of insulation from the other end- you now have a gro... | |
Tinned Copper Cable vs. Bare Copper Cable for speaker wire? @jayctoy - I do actually have my own DIY Helix cables - see this link for details My Audio Alchemy (image99.net) Unfortunately, performance comes at a price and the link above only promotes the best performing cables to date - as such, they ma... | |
Tinned Copper Cable vs. Bare Copper Cable for speaker wire? @1xtechnologies - Having tried many wires over the past couple of years my preference is for a solid bare wire (no insulation), but this leads to the problem of oxidizing.Tinning may provide a partial solution, but mixiing metals degrades performa... | |
What is the order of importance of the parts of an analogue rig? @sokogear - there are a couple of things I consider very Important in an analogue setup using a Rega TT...I guess this could be considered part of the Tone Arm, but the "method" attaching the TT to the phono stage - i.e. "the interconnect". You ca... | |
Phono stage hum - Rega Aria OK - this may be the problem ...- the Aria is not "grounded" via the mains cable - it’s ground point is "relative" to the neutral side of its circuit - which SHOULD be at ZERO volts- the images I have seen shows ONLY a 2 pin mains socket.Even if t... | |
Duelund conversion to DIY Helix Geometry Cabling @facten - welcome to the Helix Club :-)As @wig said - give them a couple of hundred hours burn-in for a stable sound - they will still improve a little after that - generally a bit more in the area of fine details.They can exhibit some strange beh... | |
Duelund conversion to DIY Helix Geometry Cabling Speaker Cable Update - with just over 250 hours on the cables they are settling down nicelyThere were some moments where things got "Twilight Zone" strange, but they did not lastThe improvement I was most intrigued by was the perception of three ... | |
Duelund conversion to DIY Helix Geometry Cabling I was recently asked...Do you consider these cables shielded? For example, could the ICs be used on a phono stage and keep noise out?And here was my response...---------------------------------I've had some good and one bad result in this area. I ... | |
Biggest "pleasant surprise" components you have owned? My DIY Helix Power, Interconnect and Speaker Cables.YES - I consider them just as important as componentsMy DIY journey started around 10 years ago with some pretty standard cables using bulk wire and pricey connectors. Then after reading many art... | |
Duelund conversion to DIY Helix Geometry Cabling @rx8man - thanks for the post - the enamel "insulation" has Dielectric Constant of around 3.2, which is higher than Teflon. But now I am left wondering if the thickness of the insulation plays a significant role.Like @stringreen posted - It woul... | |
Duelund conversion to DIY Helix Geometry Cabling WRT bare wire - the one advantage of the PVC tube is it is perfectly clear, so I can see any oxidation. The wire is very bright right now and easily seen.I'm wondering if coating the wire with a very thin coat varnish or urethane would work?Anyone... | |
Duelund conversion to DIY Helix Geometry Cabling Speaker Cable Update. Bare 14 gauge Neotech Solid wire inside PVC tube...First - I would NOT recommend the PVC tube for any cable over 6-7ft long, simply because the PVC is quite supple and "grippy", which makes inserting the bare wire quite troub... | |
Excess speaker wire @ludwig99 It may be better to use a shorter cable for one side.- - some people will not agree- it does make using those cables elsewhere a problem- a friend has the same problem so he used a shorter cable on one channel and is very happyCoiling an... | |
Bluesound Vault Combined with Node 2 @llary - You can improve the sound of the Bluesound considerably - if you use good power cable and IC's - to the point where a separate DAC is no longer required. Good power cables are the best bang for the buckAll my Bluesound devices have great ... | |
Duelund conversion to DIY Helix Geometry Cabling Power Cable UPDATE: So today’s venture replaced the Cotton Sleeve on the power cable to my amp with the PVC tube mentioned above.The cable had been completely burned in- I removed one of the Spade connectors- inserted the wire into the tube- place... |