mawe

Responses from mawe

Good audio shops Stuttgart, Germany
Studio 26 https://www.studio26.de/  
Good audio shops Stuttgart, Germany
HiFi Studio Wittmann https://www.wittmann-hifi.de/    
Duelund conversion to DIY Helix Geometry Cabling
@williewonka  Steve, just a comment on your proposal for power cords:   According safety regulations in Europe you need to have the ground wire minimum the same size as the “life” and “neutral “ conductors.  Something you might have to mention ... 
Duelund conversion to DIY Helix Geometry Cabling
I support Steve's statements. Anything longer than 2m use XLR. Find out, if your components both sides are fully balanced internally and not using a chip to only convert input/output signal from single ended to balanced. However, I never experi... 
Duelund conversion to DIY Helix Geometry Cabling
@ ghettocowboymy favourite XLR plugs are in order of performance:Neutrik silver plated (better resolution than gold plated, best price/performance ratio)Vampire Gold plated ( if you prefer the warmer sound of gold plated, approx $12/pcs at soniccr... 
Duelund conversion to DIY Helix Geometry Cabling
@ williewonka & tennesseejedjust my understanding of purity of wires:xN - x equals number of N (nines)4N - 99.99%5N - 99.999%6N - 99.9999%May be I‘m wrong, then let me know.so the silver wire with .999 is a 5N silver.But I have compared 6N cop... 
Duelund conversion to DIY Helix Geometry Cabling
@ divertiti I have done the „outer“ coil as „airadotption“ using a 6mm Teflon tube on a 1.5sqmm wire on some power cords.For further protection I did use an additional 10mm PVC tube over the Teflon tube, (PC at 230V).It was easy to slide the wire ... 
Duelund conversion to DIY Helix Geometry Cabling
@ Steve,thx for your thoughts.I was surprised about the positive effect of the “shielded L” conductor, since the LPS only draws approx 60mA at 230VAC. This is a low current load on 2x 16 AWG wires and the induced EMI should be low. I would expect,... 
Duelund conversion to DIY Helix Geometry Cabling
Update on making a helix power cord:Wonder, if someone has done it and if so, what is your experience?What I did today:A 1m long 230V power cord tested on my DIY linear power supply for my streamer and DAC, which delivers 12VDC and 5VDC. The DAC u... 
Duelund conversion to DIY Helix Geometry Cabling
@ provstAre you using solid core or stranded wire from Neotech for the ground wires?yes, solid core. 
Duelund conversion to DIY Helix Geometry Cabling
@ provst reg VH Audio balanced IChttp//www.venhaus1.com/diysilverinterconnects.html basically it is the above linked design.I use to buy a 6 mm twisted robe from home depot which consists of min 3 smaller robes twisted together. (1€/m). I than cov... 
Duelund conversion to DIY Helix Geometry Cabling
@ provst few comments to your topics:1.) PCs 230V AC I found no difference for neutral using 2x 1,3sqmm or 1x 2,5sqmm Jantzen wire.Be aware, being in 230V country, the PE (Ground-) wire must be minimum the size of the L/N conductors. With the doub... 
Duelund conversion to DIY Helix Geometry Cabling
@ willgolf your hum , it seams to me like you have a DC voltage on your mains, or picking up some sort of RFI or EMI.And it could be, that the helix design does not filter any. A power cord that does a kind of filtering could be a multi wire cable... 
Duelund conversion to DIY Helix Geometry Cabling
SteveI think no 3. you meant UP-OFC ?? 
Duelund conversion to DIY Helix Geometry Cabling
In addition to my post above:With a „normal“ 230V AC power line the „life“+ is carrying +230V and „neutral“- is 0V. The outlet of a balanced power conditioner has +115VAC on „life“ and -115VAC on „neutral“ conductor.Therefore both conductor should...