jea48
Responses from jea48
| Left RCA out on DAC not working @painter24 said: I feel it maybe as you say; the AECO’s longer center pin may have damaged the jack. . I’m kind of resigned myself with it as I am getting a replacement, but it’s just the wait. Just a suggestion. You might as well conti... | |
| Left RCA out on DAC not working would this mean the left RCA out plug on the DAC is in someway faulty? @painter24 Ya, that could be the problem. Question is was the DAC RCA jack faulty to began with, or did the longer pin on AECO plug damage the center contact in the jack? ... | |
| Left RCA out on DAC not working @painter24, Just to narrow the problem down to the DAC left channel RCA analog out jack did you try another set of Line inputs on the preamp to make sure it's not that left channel input that causing the problem. Or even try swapping the right ... | |
| Left RCA out on DAC not working @painter24, I edited my post and added more info to it. | |
| Left RCA out on DAC not working The AECO plugs have no metal on the plug shrouds inside, apart from the pin, whatsoever. @painter24,, Is this what the plug looks like? I can see the signal ground contact on the bottom of the inside of the plug "shroud". Look at the bottom of... | |
| Left RCA out on DAC not working The DAC is relatively new; I contacted the distributor, and he thinks it’s a badly soldered ground on the inside of the chassis. If that is the case then why would the Lavri Grand ICs that have AECO plugs work? The AECO plugs have a metal strip... | |
| DC blockers - what's your experience @tunehead , Here is a thread that may help you better understand DC on the mains. DC Offset Blocker/Killer - where to buy in the USA | |
| Can I connect a DC power supply to Line 6 Micro Spider with AC "port"? How about the owner manual. Is it misprinted as well? PX-2 Power Supply Input Only use a Line 6 PX-2 power supply when powering your Micro Spider using the AC IN connection. "AC in connection." I have no idea if the circuitry inside the amp c... | |
| Can I connect a DC power supply to Line 6 Micro Spider with AC "port"? The manual says AC... PX-2 Power Supply Input Only use a Line 6 PX-2 power supply when powering your Micro Spider using the AC IN connection. . | |
| Amp biasing question @immatthewj Depends on what your intentions are. Are you planing on only checking the tube bias and then shutting the amp off and not listening to music, Then there is not any need to turn on the preamp. If you want to check the bias and then ... | |
| Wiring 2 outlets to 2 dedicated 20 amp circuits with a single 10/3 electrical wire. @rbertalotto said: So, are you saying both circuits should be run from the same leg on the panel rather than one circuit on each leg? I plan on running two 12/2 - 20amp circuits, 24’ and terminate in two quad outlet boxes......Yes/OK? And, if ... | |
| Wiring 2 outlets to 2 dedicated 20 amp circuits with a single 10/3 electrical wire. @emergingsoul said: And because of the push pull action of the circuit because it’s on alternate phases the neutral wire has no current. Not exactly... Only the unbalanced 120V loads of L1 & L2 returns on the neutral conductor to the sour... | |
| Wiring 2 outlets to 2 dedicated 20 amp circuits with a single 10/3 electrical wire. @emergingsoul said: My question focused on noise which is the issue. And if there’s no noise coming from the neutral, and the ground, assuming these are connected correctly at the panel, and the panel secures the ground via a stake in the dir... | |
| Wiring 2 outlets to 2 dedicated 20 amp circuits with a single 10/3 electrical wire. @emergingsoul I’m beginning to think you are just pulling my chain here...🤔 Where does the power that feeds your house come from? A Utility Power Company?... Somewhere outside your House there is a step down power transformer that feeds power ... | |
| Wiring 2 outlets to 2 dedicated 20 amp circuits with a single 10/3 electrical wire. @emergingsoul , Look at the first schematic diagram below. Note: Load 1 and load 2 are identical. The loads are Balanced. Note: The shared "neutral". 0 A (The shared neutral is not involved). Load 1 and load 2 are in series with one another an... |