georgehifi
Responses from georgehifi
| I need some techy help in order a preamp--resistor values. jbhiller The Khozmo is a great passive, to mate it properly you’ll need the source that ’s feeding it’s input to be at least 500ohms or less in output impedance. Then order a Khozmo 10kohm series/shunt, this will then also be a great match into yo... | |
| What Class D amps will drive a 2 ohm load some do some don’t By all means please show the do’s in Class-D, hopefully independently tested, impedance v rms wattage all at just before clipping into 8, 4 and 2ohms, the same distortion figures. | |
| What Class D amps will drive a 2 ohm load golfnutz25 posts Sorry Erik, I won't be engaging in any more of this discussion. You can find the quotes yourself if you need to see them. gdnrbob And, the Angels shall weep. gdnrbob@georgehifi , Can you just drop down the level of sarca... | |
| JADIS DEFY7, can not get it to sing mozartfan OP The Jadis Defy 7 is not the amp I would recommend with these speakers, as if you look at the impedance and phase angle of your SEAS Thor MTM they are quite difficult to drive at 80-150hz and again at 3khz,https://ibb.co/Fm8mXwDEspeci... | |
| Seeking Advice on Amp/Preamp or Integrated for Thiel PCS speakers Would have been a good amp, if in top electronic condition.Cheers George | |
| Seeking Advice on Amp/Preamp or Integrated for Thiel PCS speakers This is important for you to understand, as it tells you what the amp needs to be able to do to get the very best from those speakers.Stereophile: measured tests. Thiel PCS’s impedance magnitude (fig.1) hovers between 4 and 6 ohms over most of the... | |
| What Class D amps will drive a 2 ohm load gdnrbob @golfnutz, Give it up. No, no-one has that right to tell some to give it up, if they’re not breaking any forum posting rules, what are you, a forum cop?? gdnrbob @georgehifi , Can you just drop down the level of sarcasm and argumentati... | |
| What Class D amps will drive a 2 ohm load Admittedly those Chinese modules above, have been "tickled" a little by Pascal, http://www.pascal-audio.com/products/ like EVS "tickles" the IcePower 1200as modules, just so it takes away from being stock off the shelf. From 6 Moons Jeff Rowland... | |
| What Class D amps will drive a 2 ohm load My vote goes to D-Sonic Mine would too, when you compare the Class-D module to the $10k usd Rowland Contiuum2, as they are the same. Trouble is they both are Chinese subwoofer plate amp modules, and you could get them on Alibaba for $100 not so... | |
| Amplifier for JBL Array 1000 We drove the bigger easier to drive JBL 1400 with a pair of 60w OTL Monoblocks, and they farted away at anything above low to normal listening level, so stay away from them, I’d probably stay away from SET too. To be safe go with push pull tubes U... | |
| What Class D amps will drive a 2 ohm load dht4me ML 333 Great amp for these types of very hard loads, even if those figures below are a bit wishful, there are always losses. So exact doubling is impossible unless the 8ohm and 4ohm are understated to make the 2ohm look like it's do... | |
| What Class D amps will drive a 2 ohm load Your Mytec below measured by Stereophile, could even get it up into 2ohms at all.Stereophiles JA’s summation, "practical use with speakers whose impedance doesn’t drop below 3 ohms."No good at all with the OP’s speakers we are talking about here.2... | |
| What Class D amps will drive a 2 ohm load My original point George was that you never accept anyone's experience with Class D as valid And why should I, if you search I've listened to plenty, I will go with what I hear and what independent measured results show about their ability into... | |
| What Class D amps will drive a 2 ohm load Please don’t post your own misguided words and say they are mine, your just showing your own stupidity, and this sort of thing is not called for on these forums | |
| What Class D amps will drive a 2 ohm load You are seriously deluded, and twisting words to make yourself look like you know what your talking about, which you clearly don’t. I don’t recall ever mentioning that the ML2 monoblocks are Class-A "in this thread", that’s just a bonus, it's that... |