blindjim
Responses from blindjim
| Tampa Bay Area Audiogoners OK. Count me in too. I'm in the 33624 sip code. If I can be of any help or support in some way, don't hesitate to let me know. Given enough notice I can usually be hwereever. Although, I am unable to drive. I can drive, but it's just not a good idea. | |
| Is Bi - amping worth the trouble? Undertow Sage advice. Thanks. | |
| Is Bi - amping worth the trouble? OzzyGood question. Hope there is an answer forthcoming. | |
| Is Bi - amping worth the trouble? Ngjockey ... got it. Thank you.MarkphdGot it. As I was listening to the input you posted it started coming back to me... the vertical thing was the way I initially thought to go... with the same VK500 w/BP amps. Possibly bridged... though not at f... | |
| Von scheikert VR4jr what are you using ? the results are in... the idea about the upper bass driver not functioning off the BM's upper post is accurate. I'm still in awe... I am sure big enough to admit a mistake... I need to now, and I apologize for any issues I may have caused.Who'd ha... | |
| Is Bi - amping worth the trouble? Markphd Passive? Active? Mind clarifying the diffs from one to the other?My VK5i preamp has two sets of active outs for amps... BAT probably figured on two same amps (bridged and/or unbridged) with gain controls for each ch./side... and that's it.... | |
| Von scheikert VR4jr what are you using ? MfsoaMy point exactly! electricity follows the path of least resistance. ALWAYS. A network I think, has more resistance than brass plates. using the plates should, if they are connected internally via a net, would short out, or by pass the net. Th... | |
| Von scheikert VR4jr what are you using ? Jdodmead...it would seem so. As I understand the posting, the plates are there only to hook up to the supplied umbilical... which is still another ten or so inches above the "mystery posts", (must have been a shortage of wire somewhere), and it su... | |
| Von scheikert VR4jr what are you using ? Mfsoa I do appreciate that bit of info... I suppose it depends on who you speak with at VSA... AND maybe when... a dealer showed me, or rather told me the method I wrote about above... I called VXA too a bit thereafter on a setup issue and made me... | |
| Von scheikert VR4jr what are you using ? mfsodyou may want to have your speakers checked out. the 3 pairs of binding posts are connected to the respective drivers. tops are for all the driveers in that module.... next down are for the mid bass... and bottom most are for the low end drive... | |
| Von scheikert VR4jr what are you using ? Mfsoa ...yes. All three sets of binding posts have speaker cables attached to them... the Signature 10 bi-wire set is attached to the mid bass, and upper module binding posts... low pass on the mid bass, and high pass on the upper module. the sing... | |
| Von scheikert VR4jr what are you using ? Need shot? Try your local "Trap & skeet" club (s).I use what I've got, and not done much experimenting with other amp & preamp combos. I run a pair of BATs... VK500 w/BP, and a VK5i preamp with different tubes than stock. I keep my seconda... | |
| need advice on refinishing speakers. Do's & Don'ts Fishboatthanks.. Can you simply apply veneer over pre-exsisting veneer? ...or must you take it all down to the MDF first? | |
| need advice on refinishing speakers. Do's & Don'ts Lots of wisdom in those last few posts. I am very grateful... the vat deal never entered my mind... nor did the filling or glazing ideas. Many thanks.thank you. Surely for myself, and naturally for htose later on planning some likewise venture. | |
| Buying decision time, or Time for a sanity check? JacquescornellI've long since been a proponent of getting the Department of Transportation to place warning signs near Audio dealerships... such as "CAUTION Vehicles may abruptly leave or enter roadway without advance notice! "Aolmrd1241YES, IT’S ... |