b4icu
Responses from b4icu
| Digital XLR vs Digital RCA There is nothing wrong with the engineering approach. Alchemy was long abandoned and science had prevailed.The understanding of what is going on in a digital cable is better than ignorance. The so called digital cable is not a mystery. It was actu... | |
| Length of speaker cables Mr. dannadIt was a dubious conversation. We started out with short and thick cables between monoblocks and speakers, ended up with orchestrated BS.You was kind enough to draw the conversation off tracks as far and low as possible. Sorry, but non... | |
| Length of speaker cables Mr. dannad I’m still waiting to your answer:What is your Amp’s DF?What is your cable length?As for your claim, if 5mm apart = 0.4ohm, and 4’’ (10cm) = 1.2 ohms,than a 1 meter apart, that cables would become a high value resistors...I don’t think s... | |
| Digital XLR vs Digital RCA Digital interface:The cable shall not be an issue, if the DAC section of the receiving unit is implemented properly.The most common issue with Digital interface is Jitter. To prevent jitter a PLL is implemented over the input device, to synchroniz... | |
| Length of speaker cables Mr. dannad 1. I was not answered properly. So till then, you can post questions...for others. I’m not in your game.2. The cable’s parameter to go with, is not Fr. nor C and L.3. Even though you wish, I’m not going to play your game. 4. My cables a... | |
| Length of speaker cables Mr. dannad I need to show you nothing.Parasitic capacitance? My cables are singles. To have capacitance you need two cables (plates). Parasitic capacitance do not apply for my solution. You didn't answer my question! when you do, we can contin... | |
| Length of speaker cables Mr. dannad From study of the cables relation to load (speakers) and drive (Amp),My analysis point of view is that I need to look into the Amp's output through the speaker cables.As so, the speakers are not a part of it. It proved to be true, when... | |
| Length of speaker cables Mr. dannadYou spend so many words for nothing. Did you ever tried my way?So many did and the results were fantastic. Lets try this one:Tell me what is your Amp's DF and speaker cable length. I'll calculate for you the required #AWG.Than you impl... | |
| Length of speaker cables Mr. dannad I didn’t defined what DF is or how it is measured. Don’t blame me on that.However, we should all use it as is. You can’t go in your own way.DF is not about energy transfer. Its is about controlling the load (comlex).If you would like to... | |
| Length of speaker cables Mr. gdnrbob Do you really think and recommend to use a copper wire between your Amp and speaker as the sound tweaker (Equalizer)?I'm sorry if your taste buds would like better the sound of a poor cable over a good one.I've seen the fenomena. I wa... | |
| Length of speaker cables Mr. dannadI see no particular reason why would you argue over things that you never had tried, but only critic. This is beyond understanding. Your say about AC and Impedance are all wrong! Do homework and see: Wikipedia is explaining DF as: (ht... | |
| Length of speaker cables Hi bobAt a time you believe in what you hear, I am a guy that do engineering and science. There is a way to calculate a cable’s thickness using DF and length. So I just did. We are way beyond the acknowledgement that speaker cables do effect sound... | |
| Length of speaker cables Mr. steven0713The DF is 530 (https://www.krellhifi.com/products/solo-575-xd-mono-amplifier/technical-specifications/).It’s a relatively high DF. For 6ft a #0 AWG is recommended.But why 6ft.?As your Krell 575XD is equipped with XLR input, use as lo... | |
| Length of speaker cables HiWhat is the monoblock DF figure?The cables shall be calculated per DF and length.As higher the DF thicker the cable shall be. If your monoblocks are tube Amps, the cable is insignificunt as those Amps have very low DF.If the Amps are SS or digit... | |
| How to select a good Speaker Cable Mr. tomic601 What is the relevance of your post and IF issues on Aerospace equipment, to speaker cables or it's calculation?NONE!!!If RF/IF do have effect on audio in airborne/military equipment / systems, MIL STD 810 should take care of it. Th... |