atmasphere
Responses from atmasphere
| connecting a sub-woofer to a preamp A 'Y' adapter would be one solution. | |
| Anyone With A Class 'D' Amp Play A 4 or 2 Ohm Speaker? When a good solid state amp with good current ability, drives a wild impedance curve, like many esl’s have, and speakers like Wilsons have, it will stay close to flat across the frequency range, giving least colouration.Because of the inclusion... | |
| high frequency intermittent noise It's all resistors and it's designed to shrug off MHz range ringing because of it's crazy wide bandwidth. We had to be careful too for the same reason. | |
| Anyone With A Class 'D' Amp Play A 4 or 2 Ohm Speaker? Anyone have experience running them with Quad electrostatics, which go down to 2 ohms in the high frequencies. Â Considering for a pair of stacked quads. Most Class D amps behave as voltage sources, which is to say that they can double power as t... | |
| Technics SL1200G vs GAE Will either of those "fit" without modifying the mount? Which is to say do either of those two have the same pivot to spindle distance as the stock tonearm? And will, particularly, the Reed mount over the hole in the arm board, since it is a s... | |
| TriPlanar tonearm outward skating issue what is wrong is coming for a faulty design.I think we can all agree that all arms have compromises; nothing is perfect. Having recorded and produced LPs and also having mastered them myself though, I can safely say that amongst arms its price and... | |
| Amplification for Wilson Audio Sasha on the cheap you'll need an amp with current,What is meant by that? Enough current to drive the speaker? Or something else?We had no trouble getting excellent bass on the Sashas using our MA-1, which may or may not be a 'high current' amplifier, depending on w... | |
| high frequency intermittent noise I got my phone steaming videos last night and put it INSIDE my F5 right up against the left amp board. Nelson knows his stuff.If the amp is not properly stopped, it will be almost impossible to make this problem stop (if you will pardon the expres... | |
| Technics SL1200G vs GAE The GAE is the same machine but with fancier cosmetics as it is the Anniversary Edition. | |
| Transfiguration cartridges. What tube phono stages would you use them with ? Transfiguration Orpheus, Atma-Sphere MP-1 or MP-3.... | |
| What makes tape sound better than vinyl ? Good vinyl can have as much as 70dB dynamic range on the outer edge.Its easily higher than that (I run an LP mastering operation); but compression and tape are often the reasons why you don't see that in practice.Direct to disc recordings will not... | |
| Can a Quality Full Range Speaker be the Limiting Component in a system? I find that most 'full range' speakers aren't. If you really want the bass right, you'll need a sub, if you really want extension in the highs, a tweeter.Most full range units don't make it much below 50-60 Hz. That's a bit of a bottleneck. Becaus... | |
| Amplification for Wilson Audio Sasha on the cheap The Sasha is easy to drive and if you like tubes, most any 100 watt tube amp will do the job with plenty of bass despite the low impedance at 80Hz. | |
| On/Off switch for RM_9 Mk1 does anyone know the voltage that isneeded for switch? The switch should be rated 250VAC and at least 10 amps. I would expect these specs to be printed on the old part.The switch should be bypassed with a .01uf 1000V capacitor to prevent arcing. Its not a bad idea to install a current inrush limiter i... | |
| Phono stages employing feedback & record scratch "tic" It can be an influence, but there is more to it than that.Its the actual stability of the circuit that determines how much it will exacerbate ticks and pops. The stability is not based on feedback. Feedback can add higher ordered harmonics of its ... |