"Light Loading" Amps - Music Refence and others...


On another thread, a discussion started regarding light loading amplifiers. Since it was a discussion on Vandersteen speakers, I thought it merited an new thread, especially since there is some difference of opinion.

The principle of light loading was prposed by Roger Modjeski of Music Reference.

He said (with reference to his RM10, but applicable to all his amps):

"The amplifier is flat within 0.1dB and has low distortion of 0.3% when played below clipping on average level material. At the recommended bias current of 30mA/pair, the idling dissipation is nine watts or 75% of the tubes' rating. I estimate tube life to be 5,000 to 10,000 hours. Although higher idling currents will reduce distortion, it can also be reduced by light loading. Basically, light loading reduces the output current demand on the output tubes, allowing them to be more linear. It also reduces noise, raises damping factor, reduces distortion by 78% and allows for 80% more peak current when needed. The only loss is about 20% of the power rating or 1dB." Light loading means connecting the speaker on the tap that's one half its nominal impedance rating (i.e. the 4-ohm tap for 8-ohm speakers). For 4-ohm speakers, the he recommends running two RM-10s bridged to 70-watt monoblocks.

In the aforementioned thread, Ralph Karsten of Atma-sphere said:

"If you use the 4 ohm tap on an amplifier with a speaker of higher impedance, the output transformer will be inadequately loaded, and so it will express less of its winding ratio and more of its inter-winding capacitance. This can result in the amplifier no longer having flat frequency response. In addition, the transformer can 'ring' if inadequately loaded, which is another way of saying that it will distort.

The Merlin is an 8 ohm load, with a dip to 6 ohms or so. Its a benign load and an amplifier with an output transformer, if the transformer is designed properly, will likely work best on the 8 ohm tap. This will minimize the artifact of the transformer."

Two views. And different views from listeners, somew thinking light loading works magic, other saying differently.

What do you think of the priciple. The two technical arguments? Your experiences with light loading?
pubul57
yes Paul, lite loaded for sure....they are a wonderful combo w/the RM10. I've tried & owned some other tube amps that sounded wretched in comparison w/these speakers. They don't suffer fools lightly.

Coincident Speaker Tech Partial Eclipse II
Specifications:
Frequency Response: 30hz - 30khz
Impedance:8 ohms ( min. 7.9 - max. 10 ohms )
Sensitivity: 92 db - 1w @ 1m
w/extender feet & oversize spikes
It seems as if most owners have found light loading this particular amp works as Roger suggests it should - better. My take away is also that light loading is unlikely to be the right approach with other amps, for the reasons given by Viridian, Albert, and Ralph. Thank you for your thoughts.
Yup, the little RM-10 can go "Toe to Toe" with many of the highly regarded heavyweights out there.

Pehare. It will get even better after a couple hundred hours of seat time.
With respect to the light loading thing..... each to his own I suppose.
After reading some of the recent comments on the RM-10, went back to the 4 ohm tap for a 6 hour session last evening.
Sorry gang but the 8 ohm tap is the clear winner over here.
Seems to me Scott made an EL-84-based amp that made 25 watts. It too was class AB1. To get 35 watts though would require one to jump through a lot of hoops design-wise (most EL-84 designs don't make more than 17-20 watts, but a good portion of those are class A). Something will have to give somewhere. I suppose if you ran enough B+ you could get that kind of power without running grid current, but OTOH you might have problems with tubes holding up, and it would not surprise me that the base of the tube was putting a lot of heat into the tube socket.

This latter issue may explain why the move away from circuit boards. But I would expect that the tubes may well have to be pre-selected, or certain versions of the tube may have to be avoided.