Try this simple DIY interconnect cable.


Okay, I'd like to weigh in here on the cable issue. First, let me make it perfectly clear that I am not the world's greatest cable expert, I have never heard Valhalla's, Jena Labs, or alot of the others. I am a regular working Joe who thinks that cables do make a difference but can't afford $5k-$10k to buy them. I tried out an idea that I read on the web, and changed it a little, and I thought it sounded great on my system. So here it is, a nice sounding IC for dirt cheap. Go to the Rat Shack and get their magnet wire pack($2.99). I used the 30ga for mine, but you get 26ga and 22ga spools in the pack so you can use thicker if you like. Go to Lowe's and get the 1/4" polyethylene tubing in the icemaker parts section(25ft for $2.50) Get a couple rolls of teflon tape($1.00). Cut off 1 meter(or what you need for each channel) of tubing. Wrap it with the teflon tape in a spiral. Take your magnet wire and wrap a spiral around the entire length with about 2" spacing(18 turns per meter).Leave a couple inches extending on both ends to solder to the connectors.Then wrap the whole length again with teflon tape as a jacket.Make sure the wire gets covered - no gaps. Then thread another piece of the same guage wire down the tube and out the other end. Leave "tails" on both ends, like before. Solder your favorite RCA plug to each end using the center conductor for signal, and spiral wrapped wire for ground. The ones I used had a spring type strain relief that fit right over the teflon covered tube perfectly and looks professional. Then make one for the other channel. Takes about 2 hours total. They're flexible, sturdy, don't fall apart, look good, and sound real good on my system. Now, you can make your comments about inductance, capacitance, whatever. What we've got here is a good sounding cable with a mild level of RF rejection, teflon dielectric, reasonable spacing between conductors, for a dirt cheap price. I would like an enterprising individual with some good quality cables to make a pair of these and see how they stack up against a good commercial product. Dr. Gizmo, where I got the basic idea from, said that they were better than all his exotic stuff. I don't know about that, but they do sound good on my system. Maybe we could all get lucky and be able to save alot of cash.Probably won't beat Valhalla, but for many of us it might be good enough. Share your thoughts, please. And I would love to hear a report from someone who made them and compared.
twl
Which ground wire to use? Will any generic 12 guage wire do the work, or do I need particular wire for the ground?

Ake
Guys, you have to use very small gauge single-conductor wire. 18ga or 20ga is far too large for IC cables. I used 30ga on mine.

Ake, 12 ga is totally out of the question. Use 30ga or smaller.
for some reason I was thinking about the power cord from the same website http://www.venhaus1.com

(had know idea why).

Anyway anyone know about the ground wire used in the powercord project in his website?

sorry for the mixed up.

ake
I know only that he recommended 12 AWG stranded wire.

In the designs I have made I used 13 or 11 AWG stranded wire(had them available, no other "special" reason).
You might, as well, use some shilded cable for the ground wire(as I've done in some designs). Connect the shield only at one end with the shield of the "main" Cable.
I can't specifically tell you what (soundwise) is the difference between Shilded and non shielded ground wire as I haven't use them on the same designs.

There are some other recipes that I found work very good.
Go to the www.tnt-audio.com website and search for the TNT TTS(The Twisted Snake) DIY mains cable. It's a "must try" if you're in DIY! I realy have made many different cables but like them very much in my current setup.
I could not find "the" recommended cable, but made them of similar cables. It's the design that counts the most, I believe.
By my experience cables with several smaller AWG conductors "sound" better then a similar/same construction with only two or three bigger AWG wires!

The latest, and I'm afraid best(in my current setup), design I have made 2 days ago...
I've been reading about the Virtual Dynamics power cables on another forum (and their website) and wanted to give a try to something as close to them as i could get.
I used 7 AWG(!!!!) solid core cables, shielded them (so I got an "coaxial" cabel) for the positive and negative wire. For the ground wire i used a simple stranded 11 AWG wire. No twisting.
It's a dinossaur of a cable! I don't have to tell you how difficult it was to terminate this "cable"! It's stiff as...I don't know what to compare with. And It's a pain in the ass connecting it... But when finaly done this task I was surprised with the result! Even not "burned in" yet it sounds amazing! I've never heard such a "complete" cabel! Dynamics, soundstaging, you name it - sound amazingly effortless and lifelike! I forgot to mention I "put" them onto my CD Player. Immagine - this AWG wires for "only" a CD player!!!

But it's to unpractical to use. I will try to make some smaller AWG (10 or 11) cables to make them a little more user friendly.

Best Regards,
David.
I think it was Sean whose friend went from 30 gauge wire to conductive paint for his "interconnect". All skin!