It's just that I have never found alignment to make such a quantitative difference in apparent frequency response. But this is very subjective, I suspect.
Looking for a Warmer Sounding Phono Cartridge
I've grown tired of the sound of high end MC cartridges. Detail aplenty, but I've begun to detest to the screechinesssssss.
No, my system is not biased that way. I'd consider my system neutral. Components are listed below. The Koetsu RS sounds wonderful. The other cartridges in my rotation are the Hana ML and the Shelter 901 MK III. These are not described in the literature as very etched sounding nor very detail rich. They are mostly characterized as neutral.
My ears no longer tolerate the highs, anything above 3KHz I would estimate. My hearing disappears at about 8KHz. I don't have any hearing problems except for the loss of higher frequencies. I find also that I'm not as interested in "getting everything that's on the vinyl". Not anymore. I want warmth with quality. I listen to the "audiophile" recordings, to R&R LPs from the 70s and classical and opera from all eras. Some LPs are very good, some not so, but performance overrides the defects. I want to continue to enjoy all of them.
So I'm searching for a good quality warm sounding cartridge, MM, MI, MC or some other, doesn't matter.
I've been researching the field and have come up with these candidates:
- GradoTimber Master 3
- Shelter 501 Mk III
- Soundsmith Zephyr MK III
I was pretty sold on the 501. based mostly on the article by Michael Fremer, but a very helpful contact at Upscale Audio turned me onto the other two. His advice sounds very sound and seems to come from experience with all three.
I would like to keep the discussion limited to the above three and to cartridges less than $1500 USD, unless there's a really great one that I've missed.
Thanks for your help.
My stuff:
Koetsu RS, Hana ML, and Shelter 901, Musical Surroundings Nova II phono pre. Alternate pre is Paragon System E (tubes) and a DIY SUT with Cinemg 1254 trans, sometimes Apt Holman Preamp 1, Technics SL-1200G, Denon DP-57L, Levinson #38s preamp, Rane EQ and Crossover, Bryston 2.5B cubed amp, Revel M105 bookshelf speakers, and HSU 15" Sub.
- ...
- 71 posts total
I find that electrolytic capacitors in the signal path can give a nasty, almost digital glare to the higher frequencies. Could it be that there are electrolytics in your speaker crossover? I upgraded the crossovers in my neighbour’s higher end bookshelves, and the difference was night and day. Very much bang for buck. But if you are bent on a cartridge change, I have a higher end Koetsu and similarly priced Grado. The Grado is smoother. |
@lewm The alignment must have been way off. I never bothered with alignment over three moves. I just never thought about it. I have since been educated. Believe me, it sounded horrible. In fixing this problem I noticed that the stylus kept skipping across the LP. I think that the stylus had reached the end o its life. So there were several causes for the shrill sound. |
"stylus kept skipping across the LP..." This suggests the tonearm is hanging up on something external, like the cueing device (if you have altered VTA in connection with changing cartridges, there is a chance the tonearm is fouling the lift on the cue), or there is drag on the internal tonearm wires (can be invisible rubbing, where the internal wires enter the vertical pivot shaft). Also, if you have even a modest magnifying glass around the house, take a look to see whether the stylus is still attached to the cantilever. Also, check out the anti-skate device on your tonearm. |
@lewm Thanks for the suggestions. It was definitely a worn out stylus. As I mentioned, I really wasn't aware of the care that cartridges require. A year or so ago, when I knew a bunch more and had performed over 20 alignments I pulled the cartridge out of deep storage. It still skipped. Other cartridges sound great on the same table. So there's nothing amiss with the table. In fact, this particular arm has very smooth motion and little bearing friction. I retired the stylus assembly and replaced it with the SS R-9E. |
- 71 posts total