Why Use Aluminum for a TT Platter?


Mass I am told is a good thing when it comes to TT platters. Lloyd Walker for one extolls it's virtues and as a rule some of the better turntables like to brag about their big ..Platters. Why then would aluminum, known for it's light weight (low density) turn up as frequently as it does as a platter material. I know it is easily machined but isn't there anything better and much denser.
mechans

Showing 2 responses by hiho


Paperw8: "one of the drawbacks of direct drive turntables is the possibility that vibrations from the motor would couple into the turntable and get picked up at the cartridge. since the vibrations would likely be relatively low frequency, it would likely be in the frequency range that gets amplified in the phono stage."

You're talking about half Hertz at 33rpm. That frequency exists in ALL turntables. Direct-drive is as quiet as anything. Unless the bearing is bad quality, there is very little or no noise in DD, just like belt-drive. I would say it's even quieter than belt-drive. The motor turns at 33rpm, the same amount of rotations as the platter of a belt-drive or idler-drive, WITHOUT the fast spinning motor in a BD or ID that sometimes spins at 1800rpm, and that's 30Hz! Now, the DD platter is spinning at 33rpm by magnetic force and please tell me where the stereotype DD motor noise is coming from? The second people think the motor is underneath the platter, they immediately think it's noisy. Go take a look at the assembly of a DD table, it's a platter with a ring magnet underneath and wrapped around or above a series of coils centered by the bearing well. That's it, nothing is touching the platter, unlike the belt in BD or idler wheel in ID. It's "magnetic drive" - though I hate the use of that term in commercial products.

You can criticize DD having cogging issue but not noise. Noise in DD is the last thing I worry about.

Oops, this thread is about platter material. Sorry.

____
"there has to be some motor that turns a rotor (e.g. an induction motor) that creates the time varying magnetic field that could turn a platter by lorentz force. there will be *some* vibration in that motor."

The rotor is PART of the motor, propelled by the stator coils. There's NO extra motor to turn the rotor. The platter and the motor shares the same bearing, hence "direct drive." NOTHING is physically touch the platter outside of the bearing and rotor, no belt, no idler wheel. You can argue the magnetic force to spin the rotor creates a reverse torque energy (vibration) on the stator. But that's still a lot less vibration from other means of spinning the platter such as belt-drive and idler-drive.

Of course there will ALWAYS be some vibration, so is planet earth. Let's not nitpick here.

All I am saying is that people seem to be brainwashed by the stereotype that just because there's a motor underneath the platter of a direct-drive turntable there will automatically more vibration than a belt-drive turntable. Simply not true. To get a better illustration, take a look at the mechanical simplicity of a, say, Brinkmann Bardo DD turntable and its coreless mtor:

http://www.onahighernote.com/images/product_categories/Bardo_Magnetic_Drive_small.jpg

[url]http://www.onahighernote.com/brinkmann/?c=2>http://www.brinkmann-audio.de/inhalt/bilder/bardo2.jpg[/ur]

[url]http://www.onahighernote.com/brinkmann/?c=2


People can argue all they want about cogging and speed hunting, etc... which are true issues. Noise, again, is the last thing I worry about in a direct-drive turntable with quality bearing, which holds true for ANY turntable. If you have noisy bearing, you have a noisy turntable, not just a DD table.

I own all genres of turntables, BD, DD, and ID. They all can sound good and I like them all. DD gets a bad rep so I am compelled to comment. That's all.

Happy listening!

____